Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
Motor Control
Motor Control
«
1
…
5
6
7
8
9
10
11
»
Extruder motor doesn't turn
103
views
2
comments
0
points
Most recent by
BruceInSD
September 2016
H-bot issue - steppers move 70mm for commanded 100mm
264
views
9
comments
0
points
Most recent by
famtory
September 2016
G0 ignores Z Max Speed
37
views
0
comments
0
points
Started by
CraigM
September 2016
Z Axis Not Moving Correct Amount
138
views
3
comments
0
points
Most recent by
neoh
August 2016
How to configure for origin at left REAR (not front) on a Cartesian printer?
106
views
3
comments
0
points
Most recent by
Repetier
August 2016
Can bed move past Z max with an offset?
61
views
2
comments
0
points
Most recent by
strips
August 2016
Trajectory Smoothing setting not found in latest firmware
45
views
1
comment
0
points
Most recent by
Repetier
August 2016
HE3D Delta 180 Dual Head - Motors do not move properly for direction selected.
85
views
3
comments
0
points
Most recent by
Taxus812
August 2016
2 drivers 1 axis
92
views
2
comments
0
points
Most recent by
waterdripz
August 2016
Z axis kossel moves double steps than x and y axis in kossel mini by he3d
1.4K
views
11
comments
0
points
Most recent by
Taxus812
August 2016
Delta Homing trouble after endstop calibration
80
views
1
comment
0
points
Most recent by
Repetier
August 2016
Strange moves on Z axis dual motors
104
views
2
comments
0
points
Most recent by
Repetier
July 2016
Novice in DIY 3d Printer. X, Y and Z homing and calibration
202
views
0
comments
0
points
Started by
shaolin30
July 2016
Delta - first layer is fine, second layer crashes into bed?!
210
views
1
comment
0
points
Most recent by
dannnnsyh
July 2016
Homing problem with delta printer
672
views
3
comments
0
points
Most recent by
ME1
July 2016
[Newbie][Prusa i3 steel frame] Z axis moves really slow and doesnt go all the way up
481
views
6
comments
0
points
Most recent by
evox
June 2016
Print Circle
108
views
2
comments
0
points
Most recent by
Tanuki44
June 2016
Delta: servo motors keep moving up and down in circles
87
views
1
comment
0
points
Most recent by
Repetier
June 2016
My extruder is running instead of my motors?? :/
92
views
6
comments
0
points
Most recent by
hugetoughguy
June 2016
Eeprom parameters change
105
views
2
comments
0
points
Most recent by
ColorCopy3D
June 2016
Z Axis Homes and Moves Down, But Won't Move Up Under Manual Control
346
views
5
comments
0
points
Most recent by
Repetier
June 2016
All axis are wrong!
91
views
0
comments
0
points
Started by
jorge_magalhães
May 2016
End-stops won't stop motor.
367
views
2
comments
0
points
Most recent by
rcrocket33
May 2016
XYZ Motors turning clockwise only
109
views
1
comment
0
points
Most recent by
Remko
May 2016
Feedback loop introduction
154
views
1
comment
0
points
Most recent by
Repetier
April 2016
3,3v Signal Voltage, and motor drivers need 5v
129
views
3
comments
0
points
Most recent by
Exinferis
April 2016
Home x and y
296
views
3
comments
0
points
Most recent by
Repetier
April 2016
Z Probing coming up with an error
224
views
7
comments
0
points
Most recent by
Repetier
April 2016
Endstop distance after homing problem.
317
views
4
comments
0
points
Most recent by
Repetier
April 2016
Z Axis doesn't moving up during printing
190
views
2
comments
0
points
Most recent by
Repetier
April 2016
«
1
…
5
6
7
8
9
10
11
»