Motor Control

• G28 with laserOn

  72 views 11 comments 0 points Most recent by Georg99 July 2017
• Rambo Board Y Stepper Failing sporadically after going from 12V to 24V

  51 views 5 comments 0 points Most recent by luke321 July 2017
• Z motor stepper moves once only

  485 views 20 comments 0 points Most recent by Repetier July 2017
• TMC2100 - Step loose

  147 views 4 comments 0 points Most recent by mpl July 2017
• Any one got a Tronxy X1?

  181 views 4 comments 0 points Most recent by rixstaa July 2017
• Turning My 3d printer into a laser engraver, works fine, but I cant engrave slower than 300 mm/m.

  43 views 1 comment 0 points Most recent by Repetier July 2017
• Steppers seem to be off by a factor of 10

  90 views 5 comments 0 points Most recent by Repetier July 2017
• Fighting Noise

  69 views 4 comments 0 points Most recent by abuharsky June 2017
• Repetier for Roving Robot - Can't manually control/use scripts successfully.

  39 views 1 comment 0 points Most recent by Repetier June 2017
• Z axis speed?

  82 views 1 comment 0 points Most recent by Repetier June 2017
• CoreXY issue X&Y swapped or only forward or back and not side to side

  248 views 25 comments 0 points Most recent by recoush June 2017
• Mirror motor signals

  73 views 2 comments 0 points Most recent by Saavik24 June 2017
• wrong speed x and y axes

  127 views 13 comments 0 points Most recent by Glowlow May 2017
• Stepper motors will not move no matter what

  306 views 12 comments 0 points Most recent by dahzi May 2017
• digital current control with Ultimaker 2.1.4 mainboard

  39 views 3 comments 0 points Most recent by Repetier May 2017
• Dual motor Z axis homing

  1.2K views 28 comments 0 points Most recent by marcoleo May 2017
• Servo doesn't work after launching print

  70 views 5 comments 0 points Most recent by ptab May 2017
• Corexy steps per MM for Z axis

  148 views 6 comments 0 points Most recent by recoush April 2017
• Changed my belt configuration on CORE XY and now I can get both x & y to move in correct direction

  72 views 3 comments 0 points Most recent by SOLONOZ April 2017
• Z stepper motors move only one direction

  62 views 1 comment 0 points Most recent by Repetier April 2017
• skipping steps? rounding error?

  76 views 11 comments 0 points Most recent by remcohn March 2017
• Are my firmware settings wrong?

  142 views 5 comments 0 points Most recent by MartinH March 2017
• I have a problem with X and Y axes movements of Nozzle.

  48 views 1 comment 0 points Most recent by Repetier March 2017
• Max home direction

  53 views 1 comment 0 points Most recent by Repetier March 2017
• Z axis unwanted offset

  83 views 5 comments 0 points Most recent by MartinH March 2017
• Motors Twitching

  71 views 2 comments 0 points Most recent by Jswizzle March 2017
• delta corrections do not seem to have an effect. (fw: rev 1.0.0dev)

  37 views 0 comments 0 points Started by madarren February 2017
• Z-Axis not functioning correctly

  106 views 4 comments 0 points Most recent by cass553 February 2017
• Extruder and Z not working properly

  105 views 3 comments 0 points Most recent by cinpro February 2017
• current Dev version, Jerk values?

  69 views 4 comments 0 points Most recent by Repetier February 2017