Motor Control

• tmc2130 and two z axis

  1 view 2 comments 0 points Most recent by Herc001 April 2018
• Enabling Steppers when Energizing

  1 view 2 comments 0 points Most recent by forengineer March 2018
• Zaxis moving when i try to move x and y-axis

  1 view 2 comments 0 points Most recent by PmK March 2018
• None of my motors are moving.

  65 views 2 comments 0 points Most recent by Repetier February 2018
• Z Axis Dropping

  1 view 1 comment 0 points Most recent by Repetier February 2018
• 4th Axis

  1 view 4 comments 0 points Most recent by Repetier February 2018
• Endstop distance after homing

  1 view 12 comments 0 points Most recent by Repetier February 2018
• G0 default speed in CNC mode

  1 view 2 comments 0 points Most recent by Lexar February 2018
• Y axis wont work after moving

  1 view 2 comments 0 points Most recent by Repetier January 2018
• 3 singel controlled Z-Stepper Driver

  216 views 14 comments 0 points Most recent by Repetier January 2018
• First move 100mm longer after homing x max

  1 view 1 comment 0 points Most recent by erik23 January 2018
• output synchronised to movement

  1 view 5 comments 0 points Most recent by Georg99 January 2018
• How to implement servo in place of Z motor

  1 view 1 comment 0 points Most recent by Repetier December 2017
• CoreXY ramps vs MKS gen_l

  1 view 1 comment 0 points Most recent by Otomar December 2017
• X Y minimum speed

  1 view 6 comments 0 points Most recent by Repetier December 2017
• not moving as X_MAX_LENGTH 500 Given length

  1 view 1 comment 0 points Most recent by Repetier December 2017
• cold extrusion error override

  1 view 4 comments 0 points Most recent by rshafersr December 2017
• RADDS and DRV8825

  1 view 3 comments 0 points Most recent by EdV December 2017
• Z-axis slow

  33 views 8 comments 0 points Most recent by mebj November 2017
• Set Pin 66 on high

  27 views 1 comment 0 points Most recent by Repetier November 2017
• X motor losing steps

  236 views 6 comments 0 points Most recent by greaseMonkey October 2017
• Erratic Z axis motion

  60 views 5 comments 0 points Most recent by graybeardtx October 2017
• ZAXIS_STEPS_PER_MM no matter the value I enter my Z axis is only moving 20% of required

  334 views 4 comments 0 points Most recent by Repetier October 2017
• Homes then will move down but not up, delta

  59 views 7 comments 0 points Most recent by umitakin October 2017
• Z axis not enabling (XZ H-gantry)

  41 views 4 comments 0 points Most recent by PB2000 September 2017
• Noise between G1/G0-commands

  84 views 13 comments 0 points Most recent by Georg99 September 2017
• Direct read of HPGL

  38 views 4 comments 0 points Most recent by Georg99 September 2017
• Draws inclined lines with stairs

  36 views 9 comments 0 points Most recent by Repetier September 2017
• Draw a circle from inside repetier

  50 views 8 comments 0 points Most recent by Georg99 August 2017
• Strange geometry on small arc moves

  24 views 1 comment 0 points Most recent by Repetier August 2017