Repetier-Firmware

Child Categories

• News

  44 discussions 65 comments

• General

  513 discussions 1.9K comments

• Display & Keyboard

  172 discussions 894 comments

• Motherboard

  139 discussions 610 comments

• Extruder & Bed

  485 discussions 2.3K comments

• Motor Control

  325 discussions 1.6K comments

• Bug Reports

  200 discussions 1.1K comments

• Questions & Answers

  539 discussions 2.5K comments

• Tips & Tricks

  26 discussions 66 comments

• Feature Requests

  127 discussions 790 comments

• Read me first

  Announcement Closed 1 view 0 comments 0 points Started by RepetierSupport November 2018
• Prints all over the bed

  1 view 1 comment 0 points Most recent by Repetier November 14
• PT100 Drops to Zero for a few seconds.

  1 view 5 comments 0 points Most recent by sanjeetsingh September 22
• Nozzle travels beyond printable radius while auto bed levelling

  1 view 17 comments 0 points Most recent by GrantDonley August 28
• Exploring the Transition to Repetier Firmware Dev2 for My 3D Printer

  1 view 2 comments 0 points Most recent by jimm June 12
• Auto bed levelling

  1 view 10 comments 0 points Most recent by Repetier May 31
• z axis floating head

  1 view 22 comments 0 points Most recent by Repetier May 24
• #define END_EFFECTOR_HORIZONTAL_OFFSET 0 AND #define CARRIAGE_HORIZONTAL_OFFSET 0

  1 view 3 comments 0 points Most recent by Repetier May 20
• Z Homing Bed Leveling

  1 view 0 comments 0 points Started by SigmaFive April 24
• Multiple (3) Z steppers with 3 drivers leadscrews Want to Install a Z Inductive prox Bltouch etc.

  1 view 2 comments 0 points Most recent by recoush March 17
• What do I need to know to update the firmware for BOXZY

  1 view 4 comments 0 points Most recent by wraith March 16
• E0 to E1 Copy with separate steps control - 2 Extruders

  1 view 4 comments 0 points Most recent by Shadi February 8
• Renkforce RF2000v2 (Board 3.0 with factory-i2c-Port)

  1 view 6 comments 0 points Most recent by ndee February 6
• new from 2015 Zim from Zeepro fillement feed motors aren't turning Is it hardware or software?

  1 view 3 comments 0 points Most recent by Repetier January 23
• temistör nor workiing

  1 view 1 comment 0 points Most recent by Repetier January 22
• Two Y Steppers - Only one disables

  1 view 1 comment 0 points Most recent by jstoltz January 7
• Mac M1 Unknown Printer Firmware

  1 view 1 comment 0 points Most recent by Repetier December 2023
• 32 bit

  1 view 2 comments 0 points Most recent by trumancabral December 2023
• Wait for external signal before executing G-Code command

  1 view 6 comments 0 points Most recent by 3D_Le December 2023
• Issue with AD8495 (Type 61) Thermocouple Temp Table

  1 view 5 comments 0 points Most recent by senchik November 2023
• Extrude Command not working

  1 view 2 comments 0 points Most recent by Repetier November 2023
• Unable to flash RUMBA Board with latest Repetier Firmware

  1 view 1 comment 0 points Most recent by Repetier October 2023
• Bltouch erroring on second probe attempt

  1 view 1 comment 0 points Most recent by Repetier October 2023
• Extruder Motoren vibrieren nur

  1 view 1 comment 0 points Most recent by Kessel_Gorilla October 2023
• Z goes too up after homing

  1 view 3 comments 0 points Most recent by shero2010 September 2023
• Repetier firmware only sends wait acks. Never acknowledges any other commands.

  1 view 5 comments 0 points Most recent by Repetier July 2023
• colido compact printer settings for repetier host

  1 view 0 comments 0 points Started by daveg691 July 2023
• serial com error system io ports

  4.8K views 17 comments 0 points Most recent by Repetier June 2023
• NTC 100K B3950 Thermistor, Firmware settings

  1 view 3 comments 0 points Most recent by Ovrdose01 May 2023
• size is incorrect on the x-axis

  1 view 4 comments 0 points Most recent by Repetier May 2023
• Davinci 1.0Aio issues

  1 view 4 comments 0 points Most recent by Repetier April 2023