Bug Reports

• firmare ignoring z movement in certain gcode files?

  1 view 25 comments 0 points Most recent by Repetier October 17
• second UART for Bluetooth isnt working after upgrade from 0.9.2 to 1.0.1

  1 view 7 comments 0 points Most recent by gepardya October 1
• Home all: X/Y axis is driving against endstop

  1 view 7 comments 0 points Most recent by Repetier September 12
• Compilation Error With Arduino 1.83, "sketch\HAL.h:34:20: fatal error: avr/io.h: No such file...

  1 view 2 comments 0 points Most recent by jvbiondo May 27
• Compilação de erro arduino mega

  1 view 1 comment 0 points Most recent by Repetier May 15
• Even being correct, activating z-probe would lead to forbidden xy position

  1 view 6 comments 0 points Most recent by Repetier April 9
• missing "[" in platformio.ini file generated for 1.04dev using configurator

  1 view 1 comment 0 points Most recent by Repetier March 11
• `stepperWait' referenced in section `.text' compiliation issues

  1.4K views 6 comments 0 points Most recent by Repetier February 27
• PanelDue Sd-card

  1 view 5 comments 0 points Most recent by Repetier February 26
• 1.0.4dev homing problems -CR10S (Crealty 2.1 board)

  1 view 7 comments 0 points Most recent by Repetier February 17
• Arduino wont update k200 firmware

  1 view 2 comments 0 points Most recent by Wire_Whiz February 15
• G29 tests probe position at current head position, should test at probing positions

  1 view 5 comments 0 points Most recent by Repetier February 14
• 3D-Printer can not open new files from SD card

  1 view 2 comments 0 points Most recent by RAyWB February 12
• SdFat.h: No such file or directory (Arduino IDE v 2.1.0.5+dsfg2-4.1)

  1 view 6 comments 0 points Most recent by Repetier February 11
• sd card does not work no 1.0.2

  1 view 60 comments 0 points Most recent by Repetier January 31
• Firmware 1.0.4dev not compiling

  1 view 8 comments 0 points Most recent by Repetier January 30
• Fehlermeldung bei Kompilation

  1 view 3 comments 0 points Most recent by prakash11 January 28
• Having trouble with new printer using v 1.04 and Repetier Host. OK w/ factory Marlin using R. Host

  1 view 24 comments 0 points Most recent by Doug40 December 2018
• Repetier 0.92 on Da Vinci 2.0A

  2.8K views 11 comments 0 points Most recent by BryanByrne November 2018
• G28 First home after power on/reset VS Second home REPETIER_VERSION "1.0.2"

  1 view 2 comments 0 points Most recent by OiD November 2018
• RuRamps V1.3 and Repetier V1.0.4DEV: work only without the eeprom enabled

  1 view 9 comments 0 points Most recent by Marco67 October 2018
• LEDs control in the LCD menu doesnt work with 1.0.3DEV and RuRamps

  1 view 5 comments 0 points Most recent by Marco67 October 2018
• Melzi board with RepRapDiscount display not supported in 1.0.2

  1 view 1 comment 0 points Most recent by Repetier August 2018
• Issue with enabled "Z-Probing" on zonestar based printer with repetier 0.92.0

  1 view 7 comments 0 points Most recent by Repetier July 2018
• Just upgraded from firmware 0.92.9 to 1.0.2

  1 view 4 comments 0 points Most recent by Repetier June 2018
• Firmware 1.0.3Dev does not compile

  1 view 2 comments 0 points Most recent by casey121 June 2018
• Web Configuration Wizard shows the wrong version number.

  1 view 1 comment 0 points Most recent by Repetier June 2018
• Multi Z Endstop variable not set correctly in FW 1.0.3Dev

  1 view 0 comments 0 points Started by GoBig June 2018
• In firmware version 1.0.2 the variable MINMAX_HARDWARE_ENDSTOP_Z2 gets defined twice

  1 view 1 comment 0 points Most recent by Repetier May 2018
• Help. G33 command

  1 view 2 comments 0 points Most recent by Omnimusha May 2018