Bug Reports

Compile Error 'zBabystepsMissing' is not a member of 'Printer'

31 views 1 comment 0 points Most recent by MartinH January 2017

M226 error in optional config as input

32 views 1 comment 0 points Most recent by Repetier December 2016

Laser blinks (when using heater on the same pin)

92 views 3 comments 0 points Most recent by lttn December 2016

Printer deactivated

41 views 1 comment 0 points Most recent by Repetier December 2016

PS-ON activates automatically without instructions

112 views 3 comments 0 points Most recent by Repetier December 2016

Prusa Slic3r Not Working With Repetier Firmware Controlled Kossel Clear

163 views 3 comments 0 points Most recent by Repetier December 2016

Megatronics v3.0 on Space Monkey Gorilla. Y axis is skipping steps.

35 views 3 comments 0 points Most recent by TORROR December 2016

stutter/pause continuing off coruse x/y New issue All was fine no mods made

64 views 4 comments 0 points Most recent by Repetier November 2016

KILL_IF_SENSOR_DEFECT only enables Dry Run, then print starts

66 views 1 comment 0 points Most recent by Repetier November 2016

What happened to z axis that causes high pitched tone when trying to move motors?

71 views 4 comments 0 points Most recent by spikey1973 November 2016

Z_MAX_PIN

82 views 2 comments 0 points Most recent by badman November 2016

step per mm Failure

45 views 1 comment 0 points Most recent by Repetier October 2016

Melzi & Z-Probing

319 views 10 comments 0 points Most recent by Repetier October 2016

Extruder LCD Menu

145 views 3 comments 0 points Most recent by Tanuki44 October 2016

Delta DELTA_DIAGONAL_CORRECTION_A not applied

213 views 4 comments 0 points Most recent by forerunnert October 2016

Manual Pause VS Filament Sensor Pause Not Working Right

256 views 8 comments 0 points Most recent by shaiss September 2016

0.92 Stuttering/Stalling on Rostock MAX v2

91 views 4 comments 0 points Most recent by otherguy August 2016

Problem axis z during execution g-code

241 views 17 comments 0 points Most recent by Repetier August 2016

Compilation error: Eeprom.cpp:659: error: expected primary-expression before ')' token

230 views 4 comments 0 points Most recent by JeremySiegfried July 2016

Heaters out of control when uploading file via usb. Very dangerous bug.

64 views 1 comment 0 points Most recent by Repetier July 2016

v0.92 problem with G1 and x-axis

86 views 0 comments 0 points Started by a_sprenger July 2016

Virtual Z home in development version

65 views 3 comments 0 points Most recent by justTrying June 2016

Motor after homing in Z going down

456 views 14 comments 0 points Most recent by Repetier June 2016

Bed correction problem on CoreXY

208 views 10 comments 0 points Most recent by Repetier May 2016

Compilation error with Arduino 1.6.9, FW 0.92.9, Due+RADDS, Delta Printer

757 views 10 comments 0 points Most recent by pilot779 May 2016

delta printer stepper motor always run with same gear ratio (1/10 of the right one)

74 views 2 comments 0 points Most recent by pilot779 May 2016

Due firmware won't compile out of the box with Arduino SAM board package 1.6.7

288 views 1 comment 0 points Most recent by Repetier May 2016

error compilation in eepron.cpp (error: expected primary-expression before ';' token)