Bug Reports

• EXTn_JAM_PIN missing in configuration tool

  1 view 2 comments 0 points Most recent by Repetier January 2020
• firmare ignoring z movement in certain gcode files?

  1 view 27 comments 0 points Most recent by Repetier January 2020
• Unexpected output of M114 with ABL ON

  1 view 3 comments 0 points Most recent by Repetier December 2019
• move after z probing

  1 view 3 comments 0 points Most recent by Repetier December 2019
• repetier dev Bluetooth serial

  87 views 8 comments 0 points Most recent by ronix3 November 2019
• second UART for Bluetooth isnt working after upgrade from 0.9.2 to 1.0.1

  1 view 7 comments 0 points Most recent by gepardya October 2019
• Home all: X/Y axis is driving against endstop

  1 view 7 comments 0 points Most recent by Repetier September 2019
• Compilation Error With Arduino 1.83, "sketch\HAL.h:34:20: fatal error: avr/io.h: No such file...

  1 view 2 comments 0 points Most recent by jvbiondo May 2019
• Compilação de erro arduino mega

  1 view 1 comment 0 points Most recent by Repetier May 2019
• Even being correct, activating z-probe would lead to forbidden xy position

  1 view 6 comments 0 points Most recent by Repetier April 2019
• missing "[" in platformio.ini file generated for 1.04dev using configurator

  1 view 1 comment 0 points Most recent by Repetier March 2019
• PanelDue Sd-card

  1 view 5 comments 0 points Most recent by Repetier February 2019
• 1.0.4dev homing problems -CR10S (Crealty 2.1 board)

  1 view 7 comments 0 points Most recent by Repetier February 2019
• Arduino wont update k200 firmware

  1 view 2 comments 0 points Most recent by Wire_Whiz February 2019
• G29 tests probe position at current head position, should test at probing positions

  1 view 5 comments 0 points Most recent by Repetier February 2019
• 3D-Printer can not open new files from SD card

  1 view 2 comments 0 points Most recent by RAyWB February 2019
• SdFat.h: No such file or directory (Arduino IDE v 2.1.0.5+dsfg2-4.1)

  1 view 6 comments 0 points Most recent by Repetier February 2019
• sd card does not work no 1.0.2

  1 view 60 comments 0 points Most recent by Repetier January 2019
• Firmware 1.0.4dev not compiling

  1 view 8 comments 0 points Most recent by Repetier January 2019
• Fehlermeldung bei Kompilation

  1 view 3 comments 0 points Most recent by prakash11 January 2019
• Having trouble with new printer using v 1.04 and Repetier Host. OK w/ factory Marlin using R. Host

  1 view 24 comments 0 points Most recent by Doug40 December 2018
• G28 First home after power on/reset VS Second home REPETIER_VERSION "1.0.2"

  1 view 2 comments 0 points Most recent by OiD November 2018
• RuRamps V1.3 and Repetier V1.0.4DEV: work only without the eeprom enabled

  1 view 9 comments 0 points Most recent by Marco67 October 2018
• LEDs control in the LCD menu doesnt work with 1.0.3DEV and RuRamps

  1 view 5 comments 0 points Most recent by Marco67 October 2018
• Melzi board with RepRapDiscount display not supported in 1.0.2

  1 view 1 comment 0 points Most recent by Repetier August 2018
• Just upgraded from firmware 0.92.9 to 1.0.2

  1 view 4 comments 0 points Most recent by Repetier June 2018
• Firmware 1.0.3Dev does not compile

  1 view 2 comments 0 points Most recent by casey121 June 2018
• Web Configuration Wizard shows the wrong version number.

  1 view 1 comment 0 points Most recent by Repetier June 2018
• Multi Z Endstop variable not set correctly in FW 1.0.3Dev

  1 view 0 comments 0 points Started by GoBig June 2018
• In firmware version 1.0.2 the variable MINMAX_HARDWARE_ENDSTOP_Z2 gets defined twice

  1 view 1 comment 0 points Most recent by Repetier May 2018