Bug Reports

• Repetier 0.92 on Da Vinci 2.0A

  2.8K views 19 comments 0 points Most recent by arcticfix August 27
• PIN Belegung für Motoren ist geändert

  1 view 0 comments 0 points Started by bunnu May 2023
• Won't let me cancel Recording?

  1 view 1 comment 0 points Most recent by Repetier May 2023
• MKS-Base problem and solution for two extruders...

  587 views 5 comments 0 points Most recent by 3dGenie December 2022
• Deleting file from SD card

  1 view 1 comment 0 points Most recent by Repetier August 2022
• regression in current devel firmware - stops immediately claiming homing failed

  1 view 2 comments 0 points Most recent by Repetier May 2022
• Extrudieren Ansicht beim Pi Image Fehlerhaft nach Installation 1.1.2

  1 view 3 comments 0 points Most recent by Repetier August 2021
• DEV2: Bed leveling grid area wrong?

  1 view 19 comments 0 points Most recent by karl_ranseier April 2021
• `stepperWait' referenced in section `.text' compiliation issues

  1.4K views 9 comments 0 points Most recent by Repetier April 2021
• CNC Mode Arc Direction Problem

  1 view 4 comments 0 points Most recent by yilmazyurdakul March 2021
• DEV2: Homing if endstop is much more far away than expected

  1 view 2 comments 0 points Most recent by karl_ranseier March 2021
• Dev.2 Layer shift, Filament Sensor, Z-Bewegungen.

  1 view 14 comments 0 points Most recent by karl_ranseier March 2021
• Loss of extruder sensors when I put the SD card on a DaVinci DUO

  1 view 0 comments 0 points Started by Steph35 March 2021
• Repetier G-Code Plugin for Inkspace

  1 view 3 comments 0 points Most recent by Repetier March 2021
• z Probing

  1 view 2 comments 0 points Most recent by Ikaron January 2021
• Dev.2 + Repetier Server 1.03

  1 view 1 comment 0 points Most recent by Repetier January 2021
• DEV2: G32 not working as expected

  1 view 25 comments 0 points Most recent by Repetier January 2021
• M600 / Filament Sensor verhält sich unerwartet

  1 view 8 comments 0 points Most recent by Rossini January 2021
• BedLeveling X/Y computation incorrect for linear

  1 view 3 comments 0 points Most recent by Repetier November 2020
• Is M300 g-code working?

  48 views 6 comments 0 points Most recent by Rossini October 2020
• Homing freeze

  1 view 2 comments 0 points Most recent by furynick October 2020
• DEV: Stabilize temperature corridor

  79 views 12 comments 0 points Most recent by m0dd0 September 2020
• skipping some lines in version 1.0.4

  1 view 2 comments 0 points Most recent by lubosh August 2020
• Z_MIN & Z Probe auf dem gleichen Pin, derzeit eine sehr dumme Idee. Getestet bis 1.0.4 dev

  1 view 9 comments 0 points Most recent by Repetier June 2020
• G10 Command Unretracts itselfs

  1 view 2 comments 0 points Most recent by mtys123 April 2020
• 0.005mm skipped at each probe

  1 view 3 comments 0 points Most recent by Repetier April 2020
• Dual X Crash

  1 view 8 comments 0 points Most recent by Repetier February 2020
• Ultratronics Firmware 1.0.0: SD thermocouple MAX31855 Conflict

  1 view 4 comments 0 points Most recent by SantiVil February 2020
• Z_axis_go down after homing_and_print_in_the_air

  1 view 7 comments 0 points Most recent by fandrom February 2020
• Issue with enabled "Z-Probing" on zonestar based printer with repetier 0.92.0

  1 view 9 comments 0 points Most recent by Rentner February 2020