Recent Discussions

• Uploading gcode to repetier server freezes UI of RH

  1 view 2 comments 0 points Most recent by guffy 1:14PMBug Reports
• Repetier Serever and Duet wifi

  1 view 2 comments 0 points Most recent by flopo 1:02PMRepetier-Server
• Homing offset and no LCD display of zMin trigger

  1 view 6 comments 0 points Most recent by Havenview 11:50AMQuestions & Answers
• How to arduino mega 2560 r3 config RAMPS 1.4 show RepRapDiscount lcd full graphic controller

  1 view 0 comments 0 points Started by E25ETF 9:51AM Display & Keyboard
• Lcd display

  1 view 3 comments 0 points Most recent by Jose_g 9:04AMTips & Tricks
• Single point probing, to set Z before printing.

  1 view 1 comment 0 points Most recent by Repetier 7:35AMExtruder & Bed
• Manual Licence Reset

  1 view 1 comment 0 points Most recent by Repetier 7:28AMFeature Requests
• Funksteckdose An und Ausschalten Problem

  1 view 11 comments 0 points Most recent by Repetier 7:20AMGeneral
• Upgrade to 0.90.4 on Rpi removed heated bed and webcam

  1 view 1 comment 0 points Most recent by Repetier 7:16AMBug Reports
• Connecting from MacBook Pro 2018

  1 view 0 comments 0 points Started by chriscab83 4:18AM Repetier-Host
• RPIZ GPIO connection to Prusa I3 Mk3

  1 view 2 comments 0 points Most recent by Patto647 2:26AMRepetier-Server
• Melzi 2.0.5 Control Board and a TronXY 3X

  1 view 2 comments 0 points Most recent by Richard_Brown August 20Questions & Answers
• ADVI3 FW, printer display shows IPv6 while idle, Sebatian from ADVI says its from Repetier

  1 view 6 comments 0 points Most recent by TT_Vert August 20Questions & Answers
• 3 Color Diamond Single Nozzle and wipe tower

  1 view 0 comments 0 points Started by 3DRaft August 20 CuraEngine
• Max Printable radius

  1 view 6 comments 0 points Most recent by Repetier August 20Repetier-Host
• New Pi3B+ image work?

  1 view 5 comments 0 points Most recent by Repetier August 20Bug Reports
• Repetier Ord Bot Hadron firmware?

  1 view 0 comments 0 points Started by AlexBurdov August 19 Repetier-Firmware
• SLS 3D printer: Convert Old Set up top CoreXY issue

  1 view 0 comments 0 points Started by Modi August 19 General
• 0.92 JAM_PIN, Azteeg Pro X3 Pin 19 compile failure...

  1 view 12 comments 0 points Most recent by aero August 19Repetier-Firmware
• Delta printer calibration with V1.0dev

  103 views 10 comments 0 points Most recent by Repetier August 19Repetier-Firmware
• Stream from IP camera

  1 view 7 comments 0 points Most recent by Repetier August 18Bug Reports
• Radds 1.6 or due not initializing/booting correctly on 1.0.2

  1 view 1 comment 0 points Most recent by Repetier August 18Motherboard
• "Run from here" function

  1 view 8 comments 0 points Most recent by alltrial August 18Feature Requests
• starting

  1 view 1 comment 0 points Most recent by Roko August 18General
• inductive sensors on 5v

  1 view 1 comment 0 points Most recent by Repetier August 18Questions & Answers
• Issues with Repetier-Server Free 0.90.0 - Flora-85

  1 view 6 comments 0 points Most recent by Repetier August 18Repetier-Server
• Bltouch Repetier Ramps 1.4 endstop not triggering

  1 view 3 comments 0 points Most recent by terenth August 17Questions & Answers
• Execute python script befor every print

  1 view 5 comments 0 points Most recent by Repetier August 17Questions & Answers
• Print estimates between host and server vary wildly

  1 view 1 comment 0 points Most recent by Repetier August 17Repetier-Host
• How do I fix my printer's extrusion quality

  1 view 5 comments 0 points Most recent by Repetier August 17Slic3r