Recent Discussions

• Raspi setup

  1 view 1 comment 0 points Most recent by Repetier December 2018Repetier-Server
• Connection timeout - reset send buffer block issue

  1 view 1 comment 0 points Most recent by Repetier December 2018Questions & Answers
• Translation files problem on 2.1.3

  1 view 9 comments 0 points Most recent by grumpy1 December 2018Linux
• problem with homming and manual control

  1 view 2 comments 0 points Most recent by baradov December 2018Motor Control
• Bed leveling and homing w Z-min

  1 view 3 comments 0 points Most recent by Repetier December 2018Extruder & Bed
• Server Pro on Raspberry Pi 3 - Account for "view only"

  243 views 13 comments 0 points Most recent by Repetier December 2018Repetier-Server
• Delta Calibration

  1 view 1 comment 0 points Most recent by RAyWB December 2018Repetier-Firmware
• Help: my Z axis can't stop moving down

  1 view 5 comments 0 points Most recent by minhnghia December 2018Repetier-Host
• Fan setting and control

  375 views 9 comments 0 points Most recent by Repetier December 2018General
• Not enough memory while tying to compile latest Firmware

  1 view 1 comment 0 points Most recent by Repetier December 2018General
• Repetier equivalent to Marlin M206?

  1 view 2 comments 0 points Most recent by Repetier December 2018Questions & Answers
• RepetierServer + Marlin : echo:Unknown command: "k"

  1 view 4 comments 0 points Most recent by Repetier December 2018Repetier-Server
• Help: Z axis of my delta printer cant stop moving down

  1 view 0 comments 0 points Started by minhnghia December 2018 Repetier-Firmware
• No support for right angle

  1 view 4 comments 0 points Most recent by Repetier December 2018CuraEngine
• Mysterious Temperature Settings, Configuration Wizard and Extruder Conflict

  1 view 3 comments 0 points Most recent by Repetier December 2018Slic3r
• Heated bed not working

  1 view 9 comments 0 points Most recent by CSchiavoni December 2018Extruder & Bed
• Warning: Missing Line Detected: correcting buffer usage

  118 views 20 comments 0 points Most recent by Repetier December 2018Questions & Answers
• How to change support infill via RepetierHost

  1 view 3 comments 0 points Most recent by snowgod December 2018Repetier-Host
• Building DLP 3D Printer

  1 view 1 comment 0 points Most recent by Repetier December 2018Questions & Answers
• Arduino wont update k200 firmware

  1 view 1 comment 0 points Most recent by Repetier December 2018Bug Reports
• Line Number is not Last Line Number

  1K views 6 comments 0 points Most recent by Matko December 2018Windows
• K8200 - Configuration Problems with Repetier-Server v0.90.x - Line Number is not Last Line Number+1

  1 view 1 comment 0 points Most recent by Starbase12 December 2018Questions & Answers
• Timelapse - ffmpeg - input.txt

  1 view 3 comments 0 points Most recent by Repetier December 2018Questions & Answers
• Raspi nicht mehr auffindbar

  1 view 1 comment 0 points Most recent by Repetier December 2018Repetier-Server
• 1 Printer of 7 will not communicate

  1 view 1 comment 0 points Most recent by Repetier December 2018General
• Compatible hardware Odroid-XU4

  1 view 1 comment 0 points Most recent by Repetier December 2018Repetier-Server
• Printer configuration - confused

  1 view 1 comment 0 points Most recent by Kiddow December 2018Repetier-Server
• cura3.6.0 не подключается к прошивке репитер

  1 view 0 comments 0 points Started by droid2806 December 2018 Questions & Answers
• BLTouch Configuration on Makergear M2 with Rambo

  2.4K views 10 comments 0 points Most recent by luke321 December 2018Tips & Tricks
• Infill density settings dosn't effect printout density

  196 views 7 comments 0 points Most recent by DavidP December 2018Slic3r