Recent Discussions

• Dumb question - how to connect repetier-server monitor to repetier server?

  1 view 1 comment 0 points Most recent by muzzlitebeer May 18Questions & Answers
• Z axis wont go any higher than 36.8

  1 view 6 comments 0 points Most recent by Repetier May 18Windows
• Repetier Host will not load gcode files

  1 view 2 comments 0 points Most recent by alfred0809 May 17Repetier-Host
• printer.cfg editor for Klipper instead of EEPROM editor

  1 view 6 comments 0 points Most recent by Nandox7 May 16Feature Requests
• Auto Pid tuning

  1 view 7 comments 0 points Most recent by druckich May 16Extruder & Bed
• Extruder drive wheel setup

  1 view 1 comment 0 points Most recent by Repetier May 16Extruder & Bed
• Настройка подачи филамента

  1 view 1 comment 0 points Most recent by Repetier May 16Questions & Answers
• Erster Layer = 2

  1 view 2 comments 0 points Most recent by Oxtailsoup May 15Repetier-Server
• Verbindung Repetier Server mit Anycubic (Marlin) Drucker geht verloren

  1 view 4 comments 0 points Most recent by DR3D May 15Repetier-Server
• Manuelle Verbidung zu Repetier Server mit Cura Plugin / Manually connect to Repetier Server Cura

  1 view 1 comment 0 points Most recent by Repetier May 14Repetier-Server
• SET STATIC IP on 0.93.1

  1 view 1 comment 0 points Most recent by Repetier May 14Repetier-Server
• problem with endstops

  1 view 10 comments 0 points Most recent by Repetier May 14Motor Control
• Diamond Hotend

  1 view 1 comment 0 points Most recent by Repetier May 14Questions & Answers
• Looking for best setup for 10 printer managed as a farm

  1 view 5 comments 0 points Most recent by Repetier May 13General
• Camera not working with new Raspberry Pi4 Repetier-Server

  1 view 11 comments 0 points Most recent by beathoch May 12Bug Reports
• Expected behavior of Scripts

  1 view 2 comments 0 points Most recent by 3DNewBe May 12Mac
• Identify printers by UUID

  1 view 2 comments 0 points Most recent by xunil2 May 12Feature Requests
• Z axis home problem

  1 view 1 comment 0 points Most recent by Repetier May 12Bug Reports
• Jeder druck bleibt stehen

  1 view 15 comments 0 points Most recent by Wadim May 12Bug Reports
• bed temperature fluctuation wrong

  1 view 4 comments 0 points Most recent by cropduster May 12General
• repman 3d printer connection issues

  1 view 1 comment 0 points Most recent by Repetier May 12Windows
• Go to new block position instead of previous position after tool change

  1 view 5 comments 0 points Most recent by Repetier May 12Questions & Answers
• New Build - Problem getting hotend to heat

  1 view 3 comments 0 points Most recent by Repetier May 12Repetier-Firmware
• Where are the config files with "End g-code" hidden? ;-)

  1 view 6 comments 0 points Most recent by 3DNewBe May 11Mac
• Temperatur Anzeige

  1 view 3 comments 0 points Most recent by Repetier May 11Repetier-Server
• Monitoring a Duet (RepRap fw) in Repetier Server

  1 view 2 comments 0 points Most recent by bigsub May 10General
• Z probe, M119 does ZminEndStop L while Z_probe is high

  1 view 6 comments 0 points Most recent by frogmangeek May 10Extruder & Bed
• Stop print and babystep

  1 view 7 comments 0 points Most recent by Repetier May 10Repetier-Server
• The expected time to finish the print is the same time to notification

  1 view 4 comments 0 points Most recent by Repetier May 10Repetier-Informer App
• Communication timeout - reset send buffer block

  1 view 11 comments 0 points Most recent by AndreasP May 10Windows