General

• XYZ Davinci 1.0 usb disconnect after flash

  1 view 3 comments 0 points Most recent by Repetier November 9
• Unstopable hot-end ?

  1 view 4 comments 0 points Most recent by RAyWB October 24
• Power Loss

  1 view 3 comments 0 points Most recent by Repetier October 23
• Nozzle size increase not showing properly

  155 views 6 comments 0 points Most recent by Repetier October 9
• Installing software without internet...

  1 view 1 comment 0 points Most recent by Repetier September 17
• no va hacia el lado correcto al presionar boton hogar

  1 view 6 comments 0 points Most recent by luciano August 23
• Wunsch

  1 view 1 comment 0 points Most recent by Repetier August 22
• Z only going up (+)

  1 view 1 comment 0 points Most recent by Repetier August 11
• Wobbly printed lines when it should be smooth

  1 view 1 comment 0 points Most recent by Repetier August 9
• Extending the build plate (y axis)

  1 view 0 comments 0 points Started by tomasby August 7
• How to successfully pause 3D printing and turn off

  1 view 1 comment 0 points Most recent by Repetier July 25
• How to use the touch sensor

  1 view 1 comment 0 points Most recent by Roko July 25
• PID on Cocoon Create using Repetier

  1 view 1 comment 0 points Most recent by ale July 2
• Plated objects are appearing in totally random locations once sliced into Gcode, scattered on bed

  1 view 1 comment 0 points Most recent by Repetier June 18
• Extruder diameter change ignored

  1 view 3 comments 0 points Most recent by Repetier May 13
• At a complete loss (first layer issue)

  1 view 1 comment 0 points Most recent by Repetier May 13
• Reset (erase) the bedmap?

  1 view 1 comment 0 points Most recent by Roko April 29
• Z offset question

  1 view 12 comments 0 points Most recent by Repetier March 18
• Start script Repetier, versus CuraEngine Start script.

  1 view 3 comments 0 points Most recent by Repetier March 15
• How to disable a script without deleting it

  1 view 1 comment 0 points Most recent by Repetier March 5
• disable auto level function of TronXY X3A

  1 view 1 comment 0 points Most recent by Richard_Brown March 1
• New printer Creality CR10S PRO : connection ok but manual control no ok !!

  1 view 6 comments 0 points Most recent by ths February 25
• Can't select user preset filament settings

  1 view 3 comments 0 points Most recent by s130z February 21
• What Does Repetier Host Need To Connect To Boards With ATMega1284P 16MHz Chips?

  58 views 2 comments 0 points Most recent by Twistedair February 20
• how do i define center?

  1 view 1 comment 0 points Most recent by Repetier February 17
• Print not central

  1 view 2 comments 0 points Most recent by willbilly February 16
• Change / Disable the gcode that is sent after a job

  1 view 1 comment 0 points Most recent by gd360 February 2
• G92 does not zero coordinates?

  1 view 3 comments 0 points Most recent by Repetier February 1
• New Mini-Rambo: No start signal detected - forcing start

  1 view 5 comments 0 points Most recent by Repetier January 27
• turners cube not watertight in repetier-host

  1 view 1 comment 0 points Most recent by Repetier January 24