General

• Resume print after electricity brake down

  26 views 3 comments 0 points Most recent by caslor November 2017
• x axis reversed motion without any apparent changes

  38 views 5 comments 0 points Most recent by mgd November 2017
• Thermistor NTC6K523

  17 views 1 comment 0 points Most recent by Repetier October 2017
• Extruder won't reach desired temp

  33 views 3 comments 0 points Most recent by Multi1970 October 2017
• Print button behavior

  19 views 2 comments 0 points Most recent by freebeeromg October 2017
• Where to see third temp sensor value?

  46 views 4 comments 0 points Most recent by good_idea October 2017
• First Layer issues... (still)

  507 views 63 comments 0 points Most recent by Repetier October 2017
• Feed rate from G-code not being used?

  34 views 1 comment 0 points Most recent by Repetier October 2017
• Failed print question

  36 views 4 comments 0 points Most recent by Repetier October 2017
• Auto Level - manual probe deployment...

  20 views 1 comment 0 points Most recent by Repetier October 2017
• Commands returning corrupted data

  10 views 2 comments 0 points Most recent by Repetier October 2017
• Reset the visual representation of my bed

  48 views 4 comments 0 points Most recent by Repetier September 2017
• Centering of prints

  46 views 4 comments 0 points Most recent by Repetier September 2017
• print stopping with error message "mintemp triggered"

  47 views 3 comments 0 points Most recent by Repetier September 2017
• Object is smaller when loaded into Repetier Host. Why?

  48 views 3 comments 0 points Most recent by Aviatorskate September 2017
• Remove layers from g-code

  70 views 7 comments 0 points Most recent by Repetier August 2017
• Need to solve error message.

  85 views 12 comments 0 points Most recent by Repetier August 2017
• Upload to PC

  37 views 1 comment 0 points Most recent by dlw August 2017
• dual extrusion offset error

  82 views 8 comments 0 points Most recent by Repetier August 2017
• extruder stops heating, and software keeps sending code.

  44 views 6 comments 0 points Most recent by mitch25 August 2017
• extruder light goes off mid print

  23 views 2 comments 0 points Most recent by mitch25 August 2017
• Tower Position Correction

  54 views 4 comments 0 points Most recent by Pingski August 2017
• extruder heating up very slowly

  45 views 4 comments 0 points Most recent by MartinH August 2017
• Extruder stops heating mid print

  36 views 4 comments 0 points Most recent by Repetier August 2017
• Jamming on dual extrusion

  42 views 2 comments 0 points Most recent by RAyWB August 2017
• Troubleshooting X and Y servos

  28 views 1 comment 0 points Most recent by Repetier August 2017
• Not able to start a print, errors showing up in my log on repetier.

  77 views 4 comments 0 points Most recent by mitch25 August 2017
• Frozen at Turn ON extruder. Connection Problems printing. Not with "Not Extruce" in "Manual Control"

  64 views 7 comments 0 points Most recent by Repetier August 2017
• changing diameter pulley...

  33 views 1 comment 0 points Most recent by Repetier July 2017
• The second motor Z

  53 views 5 comments 0 points Most recent by Repetier July 2017