Recent Discussions

• DEV2: Homing if endstop is much more far away than expected

  1 view 2 comments 0 points Most recent by karl_ranseier March 15Bug Reports
• wifi

  1 view 2 comments 0 points Most recent by Repetier March 15Questions & Answers
• Qnap nas installation

  1 view 1 comment 0 points Most recent by Repetier March 15Linux
• Dev.2 Layer shift, Filament Sensor, Z-Bewegungen.

  1 view 14 comments 0 points Most recent by karl_ranseier March 14Bug Reports
• I want to start from zero !!!

  1 view 5 comments 0 points Most recent by Angelo March 14Linux
• Raspberry Pi 4 WLAN Verbindung nicht möglich

  1 view 2 comments 0 points Most recent by algenbrot March 14Repetier-Server
• DEV2: Clean installation not compiling

  1 view 5 comments 0 points Most recent by karl_ranseier March 13General
• Loss of extruder sensors when I put the SD card on a DaVinci DUO

  1 view 0 comments 0 points Started by Steph35 March 13 Bug Reports
• PiZero W - Keine Wlan Verbindung

  1 view 4 comments 0 points Most recent by jmhoff March 12Repetier-Server
• Vorschaubilder / ArcWelder

  1 view 1 comment 0 points Most recent by Repetier March 12Repetier-Server
• Changing Park Command move order

  1 view 2 comments 0 points Most recent by EngineeringGuy March 12Repetier-Host
• rpi server not staying on WLAN

  1 view 1 comment 0 points Most recent by Repetier March 10Repetier-Server
• Firmware error + Runout Filament Signal

  1 view 1 comment 0 points Most recent by Repetier March 10Repetier-Server
• lojsmec@outlook.com

  1 view 3 comments 0 points Most recent by Repetier March 10Repetier-Server
• object placement

  1 view 3 comments 0 points Most recent by Repetier March 10Slic3r
• Is there a UI just for the raspberry pi based display?

  1 view 1 comment 0 points Most recent by Repetier March 10General
• Dual Z motor with one driver

  1 view 3 comments 0 points Most recent by Repetier March 10Motor Control
• “Oops! I have lost my connection. Trying to reconnect now.”

  1 view 2 comments 0 points Most recent by Repetier March 10Questions & Answers
• Adhesion type "None" still creates brim

  1 view 5 comments 0 points Most recent by dkota March 9CuraEngine
• Bltoch als Z-min und einen zweiten Taster als Z-max

  1 view 6 comments 0 points Most recent by Repetier March 9Repetier-Firmware
• Repetier Firmware with FYSETC_6

  1 view 1 comment 0 points Most recent by Repetier March 9Repetier-Firmware
• repetier server close connection

  1 view 1 comment 0 points Most recent by Repetier March 9Repetier-Server
• where is the printer config file stored?

  1 view 3 comments 0 points Most recent by Repetier March 9Repetier-Server
• How can I command a single column's motor to move in a Delta printer

  1 view 7 comments 0 points Most recent by Repetier March 9Motor Control
• PSU Powered RasPi Repetier Server shut down via Alexa smart switch.

  1 view 3 comments 0 points Most recent by Repetier March 8Feature Requests
• Issue connecting my Delta 1315

  1 view 4 comments 0 points Most recent by Repetier March 8Questions & Answers
• Ton / Meldodie nach Fertigstellung des Druckvorgang?

  1 view 1 comment 0 points Most recent by Repetier March 8Questions & Answers
• Trying to buy Repetier having problems

  1 view 1 comment 0 points Most recent by RepetierSupport March 8General
• Simplify3d Pause @ Layer mit Replace funktion

  1 view 3 comments 0 points Most recent by Repetier March 8Repetier-Server
• ideaMaker und repetier server

  1 view 2 comments 0 points Most recent by Hobbit March 7Repetier-Server