Recent Discussions

• Touch Screen Interface Separate Home X/Y and Z

  1 view 5 comments 0 points Most recent by Repetier May 5Feature Requests
• RPI mit Radds 1.5 und Due, Blobs vermeiden

  1 view 7 comments 0 points Most recent by Repetier May 5Repetier-Firmware
• Waiting for command

  1 view 6 comments 0 points Most recent by iguay009 May 5Repetier-Host
• according to your defined printer limits , this print will not fit inside your printer

  1 view 5 comments 0 points Most recent by cobpanther May 4Bug Reports
• Filament-Sensor

  1 view 4 comments 0 points Most recent by Repetier May 4Repetier-Server
• Firmware updater

  1 view 8 comments 0 points Most recent by Repetier May 4Questions & Answers
• Linear Advance - does it make sense using an 8-bit board?

  1 view 3 comments 0 points Most recent by Repetier May 4Repetier-Firmware
• Ooze shield

  1 view 5 comments 0 points Most recent by Repetier May 4CuraEngine
• RADDS with TEMP_GAIN 1 results to BED-Temp always 0.0

  1 view 3 comments 0 points Most recent by Repetier May 4Repetier-Firmware
• Aufnahmen sortieren

  1 view 1 comment 0 points Most recent by Repetier May 4Repetier-Server
• missing infill patterns, cubic, honeycomb etc.

  1 view 1 comment 0 points Most recent by Repetier May 4CuraEngine
• Printer doesn't stop heating after stopping the Print

  1 view 3 comments 0 points Most recent by Repetier May 4Questions & Answers
• Einstellungen aus repetier in cura

  1 view 1 comment 0 points Most recent by Repetier May 4CuraEngine
• Mit Prusa Slicer 2.2 erstellte g-Codes sind immer die Vorschaubilder unbrauchbar.

  1 view 14 comments 0 points Most recent by 3D_Drehzahl73 May 3Bug Reports
• Heat extruder won’t reach default temperature

  1 view 1 comment 0 points Most recent by Repetier May 3Repetier-Host
• Light on/Off

  1 view 12 comments 0 points Most recent by EGOiST May 2Repetier-Server
• Dual X-axis purging over part

  1 view 3 comments 0 points Most recent by Repetier May 2Motor Control
• layers not aligned. I make a small rectangle and the sides are at 45 degrees.

  1 view 7 comments 0 points Most recent by Repetier May 2Questions & Answers
• G2 arc command doesnot seem to follow feedrate commands

  1 view 5 comments 0 points Most recent by Repetier May 2Questions & Answers
• Selecting print causes Repetier Server disconnect

  1 view 7 comments 0 points Most recent by TheJoshW May 2Repetier-Server
• Can I boot with tool T2 instead of T0 in Firmware 1.0.4

  1 view 4 comments 0 points Most recent by Mikael May 1Questions & Answers
• Randomly stop printing

  1 view 2 comments 0 points Most recent by lorenzing May 1Bug Reports
• STM32 Firmware Flash

  1 view 5 comments 0 points Most recent by lorenzing May 1Feature Requests
• filament sensor

  1 view 1 comment 0 points Most recent by Repetier May 1Extruder & Bed
• FLSUN QQ-S running Repetier firmware?

  1 view 7 comments 0 points Most recent by Repetier May 1Questions & Answers
• Multiply Max temperatur on hotend in firmware

  1 view 1 comment 0 points Most recent by Repetier May 1Questions & Answers
• My hard drive crashed. Lost everything

  1 view 1 comment 0 points Most recent by Repetier May 1General
• Drucker geht automatisch an bei Verbindung mit USB Artillery Sidewinder

  1 view 2 comments 0 points Most recent by Grillmo April 30Repetier-Server
• Problems with small arcs G2/G3

  1 view 11 comments 0 points Most recent by Tricubik April 30General
• Repetier Server with Hyperpixel 4 touchscreen?

  1 view 9 comments 0 points Most recent by cosmith71 April 30Questions & Answers