Recent Discussions

• Repetier reagiert sehr träge mit 2 Druckern

  1 view 17 comments 0 points Most recent by Repetier November 2020Questions & Answers
• Druckerform - Repetier-Host vs. Repetier-Server

  1 view 5 comments 0 points Most recent by Sio_x November 2020Questions & Answers
• sidewinder x1 zeigt keine nozzle temperatur in der headline des servers beim druck

  1 view 2 comments 0 points Most recent by jorigel November 2020Questions & Answers
• Repetier Firmware on MKS GEN L

  1 view 42 comments 0 points Most recent by Repetier November 2020Questions & Answers
• "repetier communication timeout reset send buffer block"

  1 view 13 comments 0 points Most recent by Repetier November 2020Windows
• #error You need to define Z_PROBE_PIN to use z probe!

  1 view 1 comment 0 points Most recent by Repetier November 2020Repetier-Firmware
• Small typo error

  1 view 1 comment 0 points Most recent by Repetier November 2020Repetier-Server
• Solidoodle 2 pro

  1 view 0 comments 0 points Started by Isaakwood November 2020 Questions & Answers
• Einbindung eines 3D Druckers über WLAN in Repetier-Server

  1 view 6 comments 0 points Most recent by Repetier November 2020Questions & Answers
• //callback_pf error

  1 view 2 comments 0 points Most recent by tomtom79 November 2020Questions & Answers
• gcode Upload Funktion (Monitor1.1.0) erweitern

  1 view 2 comments 0 points Most recent by benecito November 2020Repetier-Server
• Editing Gcode just hangs and never saves

  1 view 2 comments 0 points Most recent by jarabizna November 2020Repetier-Host
• Hochladedatum und Uhrzeit von gcode files falsch

  1 view 3 comments 0 points Most recent by Repetier October 2020Bug Reports
• How to turn 'Show Travel Moves' on by default?

  1 view 4 comments 0 points Most recent by Ohmarinus October 2020Windows
• Delta Printer Use Proximity sensor for auto leveling and how to set up parameters?

  812 views 4 comments 0 points Most recent by Scottty October 2020Repetier-Firmware
• Thermistor calibration

  1 view 4 comments 0 points Most recent by leadinglights October 2020Repetier-Firmware
• Motorized Bed Level Correction with 4 Independent Z Screws?

  1 view 38 comments 0 points Most recent by Repetier October 2020Questions & Answers
• Where can I correct the print time calculation ?

  1 view 5 comments 0 points Most recent by Repetier October 2020Questions & Answers
• Print recovery on server service reboot or fail

  1 view 5 comments 0 points Most recent by Repetier October 2020Questions & Answers
• Layer Shift Problem

  1 view 3 comments 0 points Most recent by Repetier October 2020Repetier-Server
• Power Loss

  1 view 10 comments 0 points Most recent by MasterCATZ October 2020General
• Total newbie trying to access firmware

  1 view 3 comments 0 points Most recent by Repetier October 2020Questions & Answers
• RADDS with TEMP_GAIN 1 results to BED-Temp always 0.0

  1 view 5 comments 0 points Most recent by Repetier October 2020Repetier-Firmware
• Extruder overhoots while heating up

  1 view 3 comments 0 points Most recent by Repetier October 2020Extruder & Bed
• Previous version request: Repetier-Server-0.92.1-win32

  1 view 1 comment 0 points Most recent by Repetier October 2020Bug Reports
• Is M300 g-code working?

  48 views 6 comments 0 points Most recent by Rossini October 2020Bug Reports
• kommunikationstimeout hoch setzen ?

  1 view 27 comments 0 points Most recent by joeko October 2020Repetier-Server
• HttpWebResponse to Get the "Pause" Flag

  1 view 5 comments 0 points Most recent by Repetier October 2020Questions & Answers
• Delta Tower Angle Adjustment

  1 view 3 comments 0 points Most recent by Cheddy October 2020Questions & Answers
• How to get and edit source code?

  1 view 0 comments 0 points Started by SallyBoy October 2020 Questions & Answers