Recent Discussions

• Preset names with new PrusaSlicer

  1 view 2 comments 0 points Most recent by Jaroslav November 28Bug Reports
• stl offsets

  1 view 4 comments 0 points Most recent by Repetier November 28CuraEngine
• Bambulab Drucker

  1 view 9 comments 0 points Most recent by Repetier November 28Repetier-Server
• image engraving setting

  1 view 5 comments 0 points Most recent by YuviiSalhan November 28Questions & Answers
• I2C Communication with Repetier-Server?

  1 view 10 comments 0 points Most recent by Repetier November 28Repetier-Server
• Filament Used Info

  1 view 1 comment 0 points Most recent by Repetier November 28Repetier-Server
• RESCUE PRINT ERROR

  1 view 3 comments 0 points Most recent by Repetier November 27Display & Keyboard
• Kobra 2 pro per USB Verbinden

  1 view 1 comment 0 points Most recent by Repetier November 24Repetier-Server
• GPIO Access

  1 view 1 comment 0 points Most recent by Repetier November 24Repetier-Host
• Print Stops and Heater shuts down, when moving from Home position toward print position

  1 view 4 comments 0 points Most recent by recoush November 23General
• Wie viel 3D Drucker kann ich an einem Pi Repetier Server Pro betreiben?

  1 view 8 comments 0 points Most recent by Repetier November 22Repetier-Server
• Issue with AD8495 (Type 61) Thermocouple Temp Table

  1 view 5 comments 0 points Most recent by senchik November 22Repetier-Firmware
• Printer Deletion Failed! Undefined

  1 view 6 comments 0 points Most recent by repman November 21Repetier-Server
• Verbindung zu Klipper über TCP/IP

  1 view 2 comments 0 points Most recent by Repetier November 21Repetier-Server
• Direct Print - Can't upload gcode into iframe

  1 view 0 comments 0 points Started by VantageDS November 21 Repetier-Server
• Heatbed temperature copying extruder temperature.

  1 view 3 comments 0 points Most recent by Repetier November 21Extruder & Bed
• X Homing Not Working

  1 view 6 comments 0 points Most recent by electricalENG November 20Questions & Answers
• Facing Puzzling Print Layer Shifts

  1 view 16 comments 0 points Most recent by allardjd November 19General
• Repetier Server "hängt" nach Druck-Start

  1 view 8 comments 0 points Most recent by Repetier November 19Repetier-Server
• Server kann nicht herunter gefahren werden

  1 view 8 comments 0 points Most recent by Printerman November 18Questions & Answers
• Repetier Server with Elegoo Neptune4Plus

  1 view 5 comments 0 points Most recent by Repetier November 18Questions & Answers
• Gcode doesn't work

  1 view 3 comments 0 points Most recent by Repetier November 17Windows
• The 3D preview and printing from the TF card work fine, but issues arise when printing via Repetier

  1 view 3 comments 0 points Most recent by Repetier November 17Repetier-Server
• Prusa / Prusaslicer: Inserting pause at layer (M117; M601) causes server to crash

  1 view 2 comments 0 points Most recent by Repetier November 17Bug Reports
• Update gcode while printing

  1 view 2 comments 0 points Most recent by Kru5sty3dp November 15Feature Requests
• filament sensor for Creality Ender 3 S1 not stopping when filament runs out

  1 view 3 comments 0 points Most recent by Repetier November 15Repetier-Server
• Problem mit Anycubic und Zonestar am Repetierserver

  1 view 1 comment 0 points Most recent by Repetier November 15Repetier-Server
• Zonestar Z9V5 pro

  1 view 3 comments 0 points Most recent by Repetier November 15Repetier-Server
• Controlling Native Klipper Printers

  1 view 5 comments 0 points Most recent by Repetier November 15Repetier-Server
• Using mjpg-streamer on Debian Bookworm

  1 view 1 comment 0 points Most recent by bill_orange November 14Tips & Tricks