Questions & Answers

• Need help setting autolevel to use 3 points rather than a grid

  1 view 2 comments 0 points Most recent by Repetier September 21
• pb de licence repetier server

  1 view 7 comments 0 points Most recent by Repetier September 21
• add 4th / 5th axis

  40 views 5 comments 0 points Most recent by RAyWB September 16
• Z axis moving nonstop when printing

  1 view 5 comments 0 points Most recent by DFL September 13
• Sensor Error

  1 view 3 comments 0 points Most recent by Ludovicotechniq September 11
• Wrong ETA (I haven't changed any settings)

  1 view 9 comments 0 points Most recent by Repetier September 10
• M600

  1 view 1 comment 0 points Most recent by Repetier September 8
• "Command not found!" messages

  1 view 9 comments 0 points Most recent by Repetier September 3
• Bottom and top layer gaps

  1 view 2 comments 0 points Most recent by Repetier August 24
• Nozzle temp Repetier temp mismatch

  1 view 1 comment 0 points Most recent by Repetier August 24
• Melzi 2.0.5 Control Board and a TronXY 3X

  1 view 2 comments 0 points Most recent by Richard_Brown August 20
• ADVI3 FW, printer display shows IPv6 while idle, Sebatian from ADVI says its from Repetier

  1 view 6 comments 0 points Most recent by TT_Vert August 20
• inductive sensors on 5v

  1 view 1 comment 0 points Most recent by Repetier August 18
• Bltouch Repetier Ramps 1.4 endstop not triggering

  1 view 3 comments 0 points Most recent by terenth August 17
• Copy ~ Duplicate Selection from server.

  1 view 1 comment 0 points Most recent by Repetier August 15
• Print problems

  1 view 5 comments 0 points Most recent by erniehatt August 8
• Bed height map problem

  1 view 2 comments 0 points Most recent by lancerios August 2
• LoadLibrary failed with error 1114: A dynamic link library (DLL) initialization routine failed

  33.7K views 18 comments 0 points Most recent by maslivak August 1
• Autoleveling used for PCB milling

  1 view 2 comments 0 points Most recent by Repetier July 26
• Can this programme control the feeding speed and retract speed?

  1 view 1 comment 0 points Most recent by Repetier July 25
• Problems with heating up printer bed and extruder

  1 view 1 comment 0 points Most recent by Repetier July 21
• dual material Y bowden configuration

  1 view 8 comments 0 points Most recent by Repetier July 21
• Druckzeitberechnung

  1 view 4 comments 0 points Most recent by spikebhv July 14
• Incessant "Wait" Commands

  221 views 15 comments 0 points Most recent by Repetier July 14
• fails to load .stl files

  1 view 7 comments 0 points Most recent by Repetier July 10
• Host reads second nozzle at constant, incorrect temperature.

  1 view 3 comments 0 points Most recent by Earth42 July 5
• Host 2.1.2 just prints once...

  1 view 2 comments 0 points Most recent by DeJe July 4
• Slic3r 1.3.1 SDCARD prints perfect, Repetier Extruder problem

  1 view 9 comments 0 points Most recent by rcp July 2
• Skeinforge milling

  1 view 3 comments 0 points Most recent by Repetier June 29
• Beeper troubles : M300 Doesn't work but M120 does...

  1 view 2 comments 0 points Most recent by Rossini June 26