Questions & Answers

• Can't jog to set z home.

  1 view 1 comment 0 points Most recent by Repetier March 2018
• Separate printing

  1 view 2 comments 0 points Most recent by davidkwant March 2018
• Newbie setting up a Due board

  1 view 13 comments 0 points Most recent by fallapartdave March 2018
• запуск 3Д принтера

  1 view 2 comments 0 points Most recent by Марат February 2018
• запуск 3Д принтера

  1 view 0 comments 0 points Started by Марат February 2018
• New maker select + when I stop a job on host it will start where last job stopped

  1 view 28 comments 0 points Most recent by TT_Vert February 2018
• Repetier adding multiplier to calibration figures and I don't know why.

  1 view 2 comments 0 points Most recent by Plodmore February 2018
• Z height min

  40 views 3 comments 0 points Most recent by Repetier February 2018
• X and Y dimension difference on prints

  1 view 3 comments 0 points Most recent by RAyWB February 2018
• How to setup dualextrusion with one hotend and two extruder

  1 view 5 comments 0 points Most recent by Repetier January 2018
• external command send to Raspberry Pi before printer on? (Raspberry Pi

  1 view 14 comments 0 points Most recent by TT_Vert January 2018
• Is it possible to setup an extruder to home, the way the XYZ axes do ?

  1 view 0 comments 0 points Started by Lauhaus January 2018
• Help! Extruder prints off center after a few layers

  1 view 5 comments 0 points Most recent by Cenzo187 January 2018
• Line Number is not last line number and random pauses

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Parameter questions for config-h file for Arduino

  1 view 4 comments 0 points Most recent by minwolf January 2018
• What gcode to have a motor run automatically when an 'end-stop' get triggered ?

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Eprom Config greyed out

  60 views 3 comments 0 points Most recent by Repetier January 2018
• Updating the temperature table

  1 view 4 comments 0 points Most recent by hayedid January 2018
• Log file

  332 views 3 comments 0 points Most recent by Repetier January 2018
• Auto levelling grid - not square?

  1 view 2 comments 0 points Most recent by rljones January 2018
• Some problems occured when I used MCU for implementing capacitive sensing

  1 view 0 comments 0 points Started by Rolae January 2018
• Connect Teacup_Firmware on Teensy3.1 to Repetier Host

  1 view 0 comments 0 points Started by kynixliu January 2018
• G33 P1 Probing Failed on new FLSUN Delta printer

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Z offset (M851) with Cura slicer

  1 view 1 comment 0 points Most recent by Repetier January 2018
• M3D printer

  1 view 3 comments 0 points Most recent by Repetier January 2018
• Calibration Cube printed very bad

  1 view 2 comments 0 points Most recent by diablex January 2018
• Print cooling fan just run if set to 100%

  1 view 4 comments 0 points Most recent by CarlJonas January 2018
• !HELP! Load/Unload Filament (Filament Swap) Mid-Print

  1 view 0 comments 0 points Started by Mcstarcoin January 2018
• Pressing "print" makes nozzle smash into print bed. How do I fix it?

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Can't slice double extruder

  1 view 1 comment 0 points Most recent by Repetier December 2017