Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Host
›
Questions & Answers
Questions & Answers
«
1
…
4
5
6
7
8
9
10
…
16
»
New maker select + when I stop a job on host it will start where last job stopped
1
view
28
comments
0
points
Most recent by
TT_Vert
February 2018
Repetier adding multiplier to calibration figures and I don't know why.
1
view
2
comments
0
points
Most recent by
Plodmore
February 2018
Z height min
40
views
3
comments
0
points
Most recent by
Repetier
February 2018
X and Y dimension difference on prints
1
view
3
comments
0
points
Most recent by
RAyWB
February 2018
How to setup dualextrusion with one hotend and two extruder
1
view
5
comments
0
points
Most recent by
Repetier
January 2018
external command send to Raspberry Pi before printer on? (Raspberry Pi
1
view
14
comments
0
points
Most recent by
TT_Vert
January 2018
Is it possible to setup an extruder to home, the way the XYZ axes do ?
1
view
0
comments
0
points
Started by
Lauhaus
January 2018
Help! Extruder prints off center after a few layers
1
view
5
comments
0
points
Most recent by
Cenzo187
January 2018
Line Number is not last line number and random pauses
1
view
1
comment
0
points
Most recent by
Repetier
January 2018
Parameter questions for config-h file for Arduino
1
view
4
comments
0
points
Most recent by
minwolf
January 2018
What gcode to have a motor run automatically when an 'end-stop' get triggered ?
1
view
1
comment
0
points
Most recent by
Repetier
January 2018
Eprom Config greyed out
60
views
3
comments
0
points
Most recent by
Repetier
January 2018
Updating the temperature table
1
view
4
comments
0
points
Most recent by
hayedid
January 2018
Log file
332
views
3
comments
0
points
Most recent by
Repetier
January 2018
Auto levelling grid - not square?
1
view
2
comments
0
points
Most recent by
rljones
January 2018
Some problems occured when I used MCU for implementing capacitive sensing
1
view
0
comments
0
points
Started by
Rolae
January 2018
Connect Teacup_Firmware on Teensy3.1 to Repetier Host
1
view
0
comments
0
points
Started by
kynixliu
January 2018
G33 P1 Probing Failed on new FLSUN Delta printer
1
view
1
comment
0
points
Most recent by
Repetier
January 2018
Z offset (M851) with Cura slicer
1
view
1
comment
0
points
Most recent by
Repetier
January 2018
M3D printer
1
view
3
comments
0
points
Most recent by
Repetier
January 2018
Calibration Cube printed very bad
1
view
2
comments
0
points
Most recent by
diablex
January 2018
Print cooling fan just run if set to 100%
1
view
4
comments
0
points
Most recent by
CarlJonas
January 2018
!HELP! Load/Unload Filament (Filament Swap) Mid-Print
1
view
0
comments
0
points
Started by
Mcstarcoin
January 2018
Pressing "print" makes nozzle smash into print bed. How do I fix it?
1
view
1
comment
0
points
Most recent by
Repetier
December 2017
Can't slice double extruder
1
view
1
comment
0
points
Most recent by
Repetier
December 2017
Repetier Host Not Responding
834
views
15
comments
0
points
Most recent by
Repetier
December 2017
nozzle tracking display during printing
1
view
5
comments
0
points
Most recent by
Repetier
December 2017
Enable Heated Bed (Marlin?)
1
view
2
comments
0
points
Most recent by
WalkerKD
December 2017
object sliced different direction than placement
32
views
3
comments
0
points
Most recent by
rshafersr
November 2017
maximum printing length
1
view
2
comments
0
points
Most recent by
rshafersr
November 2017
«
1
…
4
5
6
7
8
9
10
…
16
»