Questions & Answers

• Updating the temperature table

  1 view 4 comments 0 points Most recent by hayedid January 2018
• Log file

  332 views 3 comments 0 points Most recent by Repetier January 2018
• Auto levelling grid - not square?

  1 view 2 comments 0 points Most recent by rljones January 2018
• Some problems occured when I used MCU for implementing capacitive sensing

  1 view 0 comments 0 points Started by Rolae January 2018
• Connect Teacup_Firmware on Teensy3.1 to Repetier Host

  1 view 0 comments 0 points Started by kynixliu January 2018
• G33 P1 Probing Failed on new FLSUN Delta printer

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Z offset (M851) with Cura slicer

  1 view 1 comment 0 points Most recent by Repetier January 2018
• M3D printer

  1 view 3 comments 0 points Most recent by Repetier January 2018
• Calibration Cube printed very bad

  1 view 2 comments 0 points Most recent by diablex January 2018
• Print cooling fan just run if set to 100%

  1 view 4 comments 0 points Most recent by CarlJonas January 2018
• !HELP! Load/Unload Filament (Filament Swap) Mid-Print

  1 view 0 comments 0 points Started by Mcstarcoin January 2018
• Pressing "print" makes nozzle smash into print bed. How do I fix it?

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Can't slice double extruder

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Repetier Host Not Responding

  834 views 15 comments 0 points Most recent by Repetier December 2017
• nozzle tracking display during printing

  1 view 5 comments 0 points Most recent by Repetier December 2017
• Enable Heated Bed (Marlin?)

  1 view 2 comments 0 points Most recent by WalkerKD December 2017
• object sliced different direction than placement

  32 views 3 comments 0 points Most recent by rshafersr November 2017
• maximum printing length

  1 view 2 comments 0 points Most recent by rshafersr November 2017
• hole diameter dimension

  1 view 1 comment 0 points Most recent by Repetier November 2017
• MKS TFT32 to Repetier

  1 view 1 comment 0 points Most recent by Repetier November 2017
• G32 returns different Printer height than measured height

  35 views 3 comments 0 points Most recent by Repetier November 2017
• Could a Delta Printer Like This Work?

  64 views 7 comments 0 points Most recent by Repetier November 2017
• Need help with Auto bed leveling.

  71 views 10 comments 0 points Most recent by Sazabi October 2017
• bed height during printing--help some kids out

  28 views 1 comment 0 points Most recent by Repetier October 2017
• Setting Z-Axis on an A8 without Auto Leveling Repetier Firmware

  34 views 1 comment 0 points Most recent by M1lQU3 October 2017
• 255 checksum error

  23 views 1 comment 0 points Most recent by Repetier October 2017
• Ghost lines? Not following gcode

  27 views 2 comments 0 points Most recent by Repetier October 2017
• Repetier für BL-Touch an einem RADDS 1.5 einstellen

  262 views 11 comments 0 points Most recent by MrZortrax October 2017
• 2 parts on top of each other

  28 views 3 comments 0 points Most recent by Repetier October 2017
• WebCam Settings

  27 views 1 comment 0 points Most recent by Repetier October 2017