Questions & Answers

• all endstops showing "hit", no directional movement available

  48 views 3 comments 0 points Most recent by rshafersr July 2017
• Heatbed wont turn on after converting Wanhao duplicator I3 from Melzi to RAMPS

  94 views 9 comments 0 points Most recent by Repetier July 2017
• How to move beyond the end stop, without disabling boundaries?

  214 views 8 comments 0 points Most recent by Repetier July 2017
• The best feed rate

  57 views 1 comment 0 points Most recent by Repetier July 2017
• Davinci 1.0a not outputting fillament after starting print

  42 views 1 comment 0 points Most recent by Roko June 2017
• Leveling Hot End to Print Surface

  47 views 1 comment 0 points Most recent by Repetier June 2017
• Calibration on LCD

  48 views 3 comments 0 points Most recent by Repetier June 2017
• How to set Z distance in initial setup

  71 views 1 comment 0 points Most recent by Repetier June 2017
• Firmware EEPROM Configuration

  162 views 4 comments 0 points Most recent by Leo June 2017
• Setting X, Y and Z Steps in Version 2.0.1

  53 views 1 comment 0 points Most recent by Repetier June 2017
• Print not printing?

  54 views 3 comments 0 points Most recent by Repetier June 2017
• how do i see travel animation

  57 views 12 comments 0 points Most recent by hardgore June 2017
• Shortcut for Print

  33 views 2 comments 0 points Most recent by jjurban55 June 2017
• "The flow rate has this not be changed" (Feedrate and Flowrate under Manual Control)

  69 views 3 comments 0 points Most recent by Repetier May 2017
• herring bone

  16 views 1 comment 0 points Most recent by Repetier May 2017
• Missing exterior between print preview and actual print

  76 views 11 comments 0 points Most recent by Repetier May 2017
• Possible to home two axises at same time?

  59 views 2 comments 0 points Most recent by jjurban55 May 2017
• XYZ motors not moving when printing

  179 views 17 comments 0 points Most recent by Repetier May 2017
• Increasing extrusion speed

  91 views 2 comments 0 points Most recent by ribbit May 2017
• Pause did not pause

  62 views 2 comments 0 points Most recent by JanComputerman May 2017
• Real-time G-Code based off sensor output?

  35 views 1 comment 0 points Most recent by Repetier May 2017
• Configuration Dimensions

  85 views 1 comment 0 points Most recent by Repetier May 2017
• Set temperature with filament settings

  138 views 3 comments 0 points Most recent by Repetier May 2017
• Single/double arrows in manual extruder feed.

  30 views 1 comment 0 points Most recent by Repetier May 2017
• Nach Update kein Z Offset für ABL mehr wirksam

  146 views 6 comments 0 points Most recent by Marcel April 2017
• Extruder steps/mm calibration

  539 views 2 comments 0 points Most recent by Repetier April 2017
• access to the port 'com6' is denied usb serial connection problem

  110 views 1 comment 0 points Most recent by Repetier April 2017
• HAL AVR vs. HAL DUE

  72 views 10 comments 0 points Most recent by RAyWB April 2017
• PWM values

  45 views 5 comments 0 points Most recent by Repetier April 2017
• Arduino Uno R3

  22 views 0 comments 0 points Started by maddy26 April 2017