Questions & Answers

• cant seem to connect to repetier with anet a8

  49 views 1 comment 0 points Most recent by Repetier October 2017
• Second Extruder Issues

  230 views 9 comments 0 points Most recent by Repetier October 2017
• Suddenly not printing well

  37 views 3 comments 0 points Most recent by Repetier October 2017
• Z probe Failed & Bed Leveling

  333 views 6 comments 0 points Most recent by EGropp September 2017
• V2.0.5 G-Code Error

  37 views 1 comment 0 points Most recent by Repetier September 2017
• Extremely weird issue after Melzi to RAMPS conversion.

  121 views 14 comments 0 points Most recent by Repetier September 2017
• Delta Printer print sizes wrong

  37 views 3 comments 0 points Most recent by Repetier September 2017
• Pulsewidth control via firmware?

  73 views 8 comments 0 points Most recent by Flux September 2017
• PWM speed adjust

  38 views 2 comments 0 points Most recent by Repetier September 2017
• Reversing extruder motor rotation

  80 views 1 comment 0 points Most recent by Repetier September 2017
• [Sherlock Holmes wanted] Y-max endstop problem / RH coordinate issue

  30 views 4 comments 0 points Most recent by PJ_L September 2017
• nozzle hitting bed

  54 views 3 comments 0 points Most recent by Repetier September 2017
• Error at install

  23 views 1 comment 0 points Most recent by Repetier September 2017
• Z probe is going beyond end stop

  33 views 1 comment 0 points Most recent by Repetier September 2017
• Bed height map tool reseting, restarting or rebooting printer

  37 views 1 comment 0 points Most recent by Repetier August 2017
• Printer in just one RPI3

  33 views 3 comments 0 points Most recent by Repetier August 2017
• Filament Selection for Slicer

  38 views 3 comments 0 points Most recent by ShaneB August 2017
• Automated Printing Issue

  41 views 3 comments 0 points Most recent by Repetier August 2017
• 3D Printer has stopped running the desired G-Code

  77 views 10 comments 0 points Most recent by Nexus August 2017
• M104 T0 S.. vs M104 S..

  35 views 1 comment 0 points Most recent by Repetier August 2017
• Z Movement only up

  47 views 5 comments 0 points Most recent by Repetier August 2017
• plugged extruder tip

  66 views 13 comments 0 points Most recent by rshafersr August 2017
• 3 endstops for z

  26 views 1 comment 0 points Most recent by Repetier August 2017
• "endstops hit: Z" stops any axis movements, how to reset?

  60 views 3 comments 0 points Most recent by rshafersr August 2017
• Printed models too small

  47 views 5 comments 0 points Most recent by Hero August 2017
• Transfer printer settnings from Cura to Repetier?

  26 views 1 comment 0 points Most recent by Repetier July 2017
• Raspberry Pi 3 running 0_85_2_v7 - How do I shut off the silly wireless access point

  45 views 3 comments 0 points Most recent by Repetier July 2017
• Does @pause still work in Repetier V2.0.1?

  30 views 3 comments 0 points Most recent by Repetier July 2017
• Repetier Host V1.06 Motor extruding backwards

  29 views 1 comment 0 points Most recent by Repetier July 2017
• NTC thermistor not registering temper over ~160

  143 views 18 comments 0 points Most recent by Repetier July 2017