Bug Reports

• Help. G33 command

  1 view 2 comments 0 points Most recent by Omnimusha May 2018
• 0.92.9 weird compiler error out of the blue

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Pause throws off X and Y Coordinates

  1 view 4 comments 0 points Most recent by Repetier March 2018
• Spell Check -Autolevle

  1 view 2 comments 0 points Most recent by Akentut March 2018
• Oscillation on bed and nozzle temprature after auto bed levelling

  1 view 6 comments 0 points Most recent by Repetier March 2018
• Tool Change Command works differently from 1.0 Dev in 04/2017

  1 view 5 comments 0 points Most recent by Doug40 March 2018
• Print offset reset after G28 in firmware 0.92.9

  1 view 5 comments 0 points Most recent by Repetier February 2018
• RADDS fans: M106 P1 doesn't activate the attached fan

  1 view 2 comments 0 points Most recent by Repetier January 2018
• turning on (even disconnected) hotend heater changes behavior of proximity sensor (1.0.0dev)

  1 view 3 comments 0 points Most recent by good_idea January 2018
• [DUE] Watchdog reset at startup after changing steps/mm in EEPROM

  1 view 5 comments 0 points Most recent by Repetier January 2018
• SAFETY ISSUE TEMP CONTROL!!!!!! MIN_DEFECT_TEMPERATURE >0 not working correct

  1 view 9 comments 0 points Most recent by Rossini December 2017
• Dual axis X2 feedrate limitation?

  1 view 5 comments 0 points Most recent by Repetier December 2017
• DEV 1.0.0 - Motherboard inssue

  1 view 2 comments 0 points Most recent by jbaiao December 2017
• Problems with loading Development firware

  1 view 0 comments 0 points Started by tpbh November 2017
• motion.h:359: error: expected '}' before 'else'

  1 view 2 comments 0 points Most recent by Rossini November 2017
• I didn't send "M105", why I will receive temperature information "T:20.25/0 B:14.56/0 ..."

  1 view 7 comments 0 points Most recent by jszxwcq November 2017
• Bed heating and auto power on

  21 views 1 comment 0 points Most recent by Repetier November 2017
• Error Flashing 1.0.0 Dev on Anet V1 board

  51 views 8 comments 0 points Most recent by BernieG October 2017
• wrong Extruder Name repetier-Host V2.0.5

  41 views 4 comments 0 points Most recent by lep230 October 2017
• Dead Time - Temperature drops after hours

  23 views 1 comment 0 points Most recent by Repetier September 2017
• Configurator can't set ENDSTOP_Z_MIN_INVERTING

  18 views 2 comments 0 points Most recent by Repetier September 2017
• Z axis not working for Ultratronics boards

  19 views 1 comment 0 points Most recent by Repetier September 2017
• M999 not resetting temp sensor issues as expected

  30 views 1 comment 0 points Most recent by Repetier September 2017
• Z-Axis problem with FAST_COREXYZ and two z-axis-endstops.

  74 views 10 comments 0 points Most recent by Rossini September 2017
• Dual x axis - homing problem

  87 views 1 comment 0 points Most recent by Repetier September 2017
• Compile scope error with Rep-firmware_1.0.0DEV

  15 views 1 comment 0 points Most recent by Repetier September 2017
• DEV: G33 crashes in to X min

  35 views 5 comments 0 points Most recent by boelle August 2017
• GCodes auf einmal weg

  136 views 8 comments 0 points Most recent by Repetier July 2017
• 'TWI_CLOCK_FREQ' error when upload

  78 views 12 comments 0 points Most recent by omv1065 July 2017
• Temperature modification during Z movement !

  81 views 14 comments 0 points Most recent by Repetier July 2017