Repetier-Firmware

Child Categories

• News

  8 discussions 57 comments

• General

  350 discussions 1.8K comments

• Display & Keyboard

  148 discussions 831 comments

• Motherboard

  124 discussions 548 comments

• Extruder & Bed

  449 discussions 2.1K comments

• Motor Control

  297 discussions 1.5K comments

• Bug Reports

  194 discussions 1K comments

• Questions & Answers

  474 discussions 2.3K comments

• Tips & Tricks

  19 discussions 56 comments

• Feature Requests

  119 discussions 777 comments

• PINDA 2 support

  1 view 3 comments 0 points Most recent by Repetier January 4
• Adjusting bed leveling procedure with BL-Touch

  1 view 8 comments 0 points Most recent by WardMD90745 December 2020
• PT100 Drops to Zero for a few seconds.

  1 view 1 comment 0 points Most recent by Repetier December 2020
• Dual x axis motors problem

  1 view 2 comments 0 points Most recent by Peemchai December 2020
• Repetier CNC with TB6600

  1 view 37 comments 0 points Most recent by prakash11 December 2020
• MKS_RUMBA32 end dev2

  1 view 12 comments 0 points Most recent by Repetier November 2020
• Change Extruder,

  1 view 0 comments 0 points Started by alaalamsa November 2020
• Lost licence key

  1 view 3 comments 0 points Most recent by buddylee7 November 2020
• does not connect to host by USB

  1 view 3 comments 0 points Most recent by FlyNuga November 2020
• Hello, how to add additional A B C axis ?

  1 view 5 comments 0 points Most recent by Repetier November 2020
• #error You need to define Z_PROBE_PIN to use z probe!

  1 view 1 comment 0 points Most recent by Repetier November 2020
• Delta Printer Use Proximity sensor for auto leveling and how to set up parameters?

  812 views 4 comments 0 points Most recent by Scottty October 2020
• Thermistor calibration

  1 view 4 comments 0 points Most recent by leadinglights October 2020
• RADDS with TEMP_GAIN 1 results to BED-Temp always 0.0

  1 view 5 comments 0 points Most recent by Repetier October 2020
• Dev2: "RUMBA32_F446VE" no found

  1 view 4 comments 0 points Most recent by frguy October 2020
• Button To inject Gcode

  1 view 4 comments 0 points Most recent by Virtualchronos October 2020
• dev2: Leveling and Bump Correction Question

  1 view 3 comments 0 points Most recent by Repetier October 2020
• dev2: Problems with offset Values, Dual Extrusion & BLTouch

  1 view 13 comments 0 points Most recent by Scottty October 2020
• M81 mit S1 funktioniert nicht

  1 view 2 comments 0 points Most recent by joeko October 2020
• Dev2 - I can’t activate the Jam control

  1 view 5 comments 0 points Most recent by frguy October 2020
• Understanding Z-Probing

  1 view 1 comment 0 points Most recent by Repetier October 2020
• Squarish Circles

  1 view 3 comments 0 points Most recent by Repetier October 2020
• Help with bltouch

  1 view 9 comments 0 points Most recent by Repetier October 2020
• DEV2 - TOOL_EXTRUDER gcode fail

  1 view 13 comments 0 points Most recent by frguy October 2020
• Ultratronics Pro with BTT TFT7.0

  1 view 3 comments 0 points Most recent by Repetier October 2020
• About G32 initial move necessity

  1 view 2 comments 0 points Most recent by lmcbmai October 2020
• G02 and G03 code issue

  1 view 6 comments 0 points Most recent by bpetrus September 2020
• Move the non current Extruder on Toolchange

  1 view 1 comment 0 points Most recent by Repetier September 2020
• Experience RUMBA32 installation (and upload problem)

  1 view 29 comments 0 points Most recent by karl_ranseier September 2020
• Dev2 - "SD" menu does not appear.

  1 view 2 comments 0 points Most recent by frguy September 2020