Repetier-Firmware

Child Categories

• News

  6 discussions 36 comments

• General

  280 discussions 1.4K comments

• Display & Keyboard

  127 discussions 719 comments

• Motherboard

  98 discussions 435 comments

• Extruder & Bed

  382 discussions 1.8K comments

• Motor Control

  248 discussions 1.2K comments

• Bug Reports

  166 discussions 837 comments

• Questions & Answers

  369 discussions 1.7K comments

• Tips & Tricks

  13 discussions 38 comments

• Feature Requests

  106 discussions 729 comments

• could not activate Z probe error

  1 view 6 comments 0 points Most recent by MartinH January 2018
• ARDUINO IDE VERSION

  1 view 5 comments 0 points Most recent by renei January 2018
• I have enabled CNC milling support. #define SUPPORT_CNC 1 #define CNC_WAIT_ON_ENABLE 300 #define CN

  1 view 3 comments 0 points Most recent by Mauro January 2018
• Linear advance and M900

  1 view 21 comments 0 points Most recent by Repetier January 2018
• Best way to add a new screen support?

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Is it possible to independently z calibrate 2 extruders

  1 view 6 comments 0 points Most recent by overdrive January 2018
• GAMEDUINO2

  328 views 7 comments 0 points Most recent by RAyWB January 2018
• Microswitch initiated pause during SD print

  1 view 2 comments 0 points Most recent by Repetier January 2018
• printing mirrored Core XY

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Question about dual extruder

  1 view 7 comments 0 points Most recent by Repetier January 2018
• Problems with distortion correction - V1.0dev

  1 view 8 comments 0 points Most recent by Jagi January 2018
• Arduino Due will upload Repetier firmware from Arduino IDE but wont run on DUE/RADDS

  131 views 8 comments 0 points Most recent by wfpaez January 2018
• Can't start print "could not activate z"

  1 view 4 comments 0 points Most recent by Repetier January 2018
• Autoleveling with Ultratronics pro v1

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Jam detection immediate action

  1 view 9 comments 0 points Most recent by Repetier January 2018
• Lost licence key

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Core-XY: park the nozzle to another position after G28

  1 view 2 comments 0 points Most recent by Repetier January 2018
• diamond hot end extruder

  1 view 7 comments 0 points Most recent by Repetier January 2018
• Ultratronic pro v1 autoleveling

  1 view 1 comment 0 points Most recent by Repetier January 2018
• M106 commands with P0, P1, P2 etc addresses to the same print cooling fan, not others

  1 view 3 comments 0 points Most recent by good_idea January 2018
• Questions about dual X axis and Z2 end stop

  1 view 3 comments 0 points Most recent by Repetier January 2018
• Speed multipier vs. max feedrate

  1 view 5 comments 0 points Most recent by Repetier January 2018
• "Squashed" Prints after RAMPS from Melzi

  1 view 11 comments 0 points Most recent by MartinH January 2018
• TMC2130 and Repetier Firmware

  1 view 2 comments 0 points Most recent by alexsomesan January 2018
• Trouble setting home z axis Tevo Tarantula - M851

  1 view 2 comments 0 points Most recent by Roko January 2018
• Problem about M3 command

  1 view 9 comments 0 points Most recent by Repetier December 2017
• About the command "M3/M4/M5"

  1 view 3 comments 0 points Most recent by Repetier December 2017
• issue with bed levelling

  1 view 2 comments 0 points Most recent by samuelk December 2017
• Retraction on extruder switch doesn't work for me

  1 view 4 comments 0 points Most recent by rhklein December 2017
• dac error

  168 views 18 comments 0 points Most recent by eddiefirth December 2017