Repetier-Firmware

Child Categories

• News

  15 discussions 64 comments

• General

  381 discussions 1.9K comments

• Display & Keyboard

  159 discussions 871 comments

• Motherboard

  133 discussions 589 comments

• Extruder & Bed

  473 discussions 2.2K comments

• Motor Control

  315 discussions 1.6K comments

• Bug Reports

  200 discussions 1.1K comments

• Questions & Answers

  511 discussions 2.5K comments

• Tips & Tricks

  25 discussions 66 comments

• Feature Requests

  122 discussions 782 comments

• DISPLAY SELECTION

  1 view 3 comments 0 points Most recent by Repetier August 2020
• Recommanded Jerk Acceleration and speed.

  1 view 1 comment 0 points Most recent by Repetier August 2020
• Reduced feedrate on 2nd reference Pass.

  1 view 5 comments 0 points Most recent by Repetier August 2020
• Limit Switches and homing switches

  1 view 2 comments 0 points Most recent by mendelevium August 2020
• UART rx0 tx0 help needed

  1 view 8 comments 0 points Most recent by Virtualchronos August 2020
• assigning pins

  1 view 7 comments 0 points Most recent by Repetier July 2020
• z-Correction Enabled....but no working

  1 view 3 comments 0 points Most recent by Repetier July 2020
• Y stepper has no current till print starts.

  1 view 4 comments 0 points Most recent by Jannie July 2020
• My prints are not centered

  1 view 3 comments 0 points Most recent by Repetier July 2020
• Bed-leveling - Probe grinds over surface between measured point

  1 view 5 comments 0 points Most recent by Repetier June 2020
• Davinci I.0-A flashing problems

  1 view 3 comments 0 points Most recent by Repetier June 2020
• Custom Kinematics

  1 view 13 comments 0 points Most recent by ttnd June 2020
• Enable Z-probing

  1 view 7 comments 0 points Most recent by Repetier June 2020
• Laser Add-on

  100 views 10 comments 0 points Most recent by AmyRubin June 2020
• Thermocouple error

  1 view 10 comments 0 points Most recent by Gromovnik June 2020
• Z Probe and min Z appear to be mutually exclusive

  1 view 2 comments 0 points Most recent by Zebethyal June 2020
• New Build - Problem getting hotend to heat

  1 view 3 comments 0 points Most recent by Repetier May 2020
• Moving from 0.92.9 to 1.0x firmware

  1 view 4 comments 0 points Most recent by touchthebitum May 2020
• RPI mit Radds 1.5 und Due, Blobs vermeiden

  1 view 7 comments 0 points Most recent by Repetier May 2020
• Linear Advance - does it make sense using an 8-bit board?

  1 view 3 comments 0 points Most recent by Repetier May 2020
• Firmware Update without configuration.h

  1 view 11 comments 0 points Most recent by Repetier April 2020
• Hotend not heating

  1 view 3 comments 0 points Most recent by zinktiti April 2020
• Autolevel bed error

  463 views 16 comments 0 points Most recent by brzozkowski April 2020
• DUAL Z management with FEATURE_TWO_ZSTEPPER 1

  1 view 12 comments 0 points Most recent by renei April 2020
• Filament Runout Ground Zero

  1 view 4 comments 0 points Most recent by OldEngineer April 2020
• Rumba board no communication since failed firmware update via repetier server

  1 view 6 comments 0 points Most recent by Scottty April 2020
• Dual Parking extruder

  1 view 2 comments 0 points Most recent by Serenitas April 2020
• HE3D 2 in 1 out extruders not working

  1 view 15 comments 0 points Most recent by eaton_chip April 2020
• Autoleveling P1, P2 and P3 position - Out of bed measures

  1 view 3 comments 0 points Most recent by FricPT April 2020
• Babystepping stops working mid print

  1 view 5 comments 0 points Most recent by Repetier April 2020