Motor Control

• I have a problem with X and Y axes movements of Nozzle.

  48 views 1 comment 0 points Most recent by Repetier March 2017
• Max home direction

  53 views 1 comment 0 points Most recent by Repetier March 2017
• Z axis unwanted offset

  83 views 5 comments 0 points Most recent by MartinH March 2017
• Motors Twitching

  71 views 2 comments 0 points Most recent by Jswizzle March 2017
• delta corrections do not seem to have an effect. (fw: rev 1.0.0dev)

  37 views 0 comments 0 points Started by madarren February 2017
• Z-Axis not functioning correctly

  106 views 4 comments 0 points Most recent by cass553 February 2017
• Extruder and Z not working properly

  105 views 3 comments 0 points Most recent by cinpro February 2017
• current Dev version, Jerk values?

  69 views 4 comments 0 points Most recent by Repetier February 2017
• Chasing an X vs Y movement issue on a DELTA....checking Steps/mm

  135 views 4 comments 0 points Most recent by madarren February 2017
• Z Homing Question

  179 views 5 comments 0 points Most recent by Michał February 2017
• Motors lurching

  102 views 7 comments 0 points Most recent by Jswizzle January 2017
• Smoother ARC support

  181 views 3 comments 0 points Most recent by Lexar January 2017
• Head crash when moving past 1mm

  155 views 15 comments 0 points Most recent by Poida January 2017
• Z homing on full step?

  49 views 1 comment 0 points Most recent by Repetier January 2017
• 'Move axes when homed' in firmware 1.0

  113 views 7 comments 0 points Most recent by Tanuki44 January 2017
• X Y stepper disabled after movement Rostock delta

  177 views 11 comments 0 points Most recent by Repetier January 2017
• Configuring Z-Axis confusion

  178 views 4 comments 0 points Most recent by SvdSinner January 2017
• Firmware will not change Steps/MM

  82 views 3 comments 0 points Most recent by Repetier January 2017
• My Da Vinci 1.0 will not move any axis with repetier firm.

  58 views 1 comment 0 points Most recent by Repetier December 2016
• Add a New M-code

  53 views 0 comments 0 points Started by jeremiel December 2016
• Z axis motor not working after re upload

  204 views 13 comments 0 points Most recent by unknown28 December 2016
• strange homing back move behaviour on y-axis (Delta printer)

  87 views 1 comment 0 points Most recent by printjob November 2016
• Stunning stepper motor

  79 views 1 comment 0 points Most recent by Repetier November 2016
• Prusa P802M, odd Z Homing

  110 views 2 comments 0 points Most recent by matthewsjl November 2016
• Reprap Prusa I3 Z axis won't move down

  603 views 2 comments 0 points Most recent by spikey1973 November 2016
• Z Axis Motor Moving very slowly

  115 views 4 comments 0 points Most recent by Repetier November 2016
• Extra stepper motor don't move

  182 views 7 comments 0 points Most recent by eric78 November 2016
• Different step for axis

  338 views 4 comments 0 points Most recent by sandro730 November 2016
• Additional ExtraMotor Gcode

  102 views 2 comments 0 points Most recent by Jpod October 2016
• Y axis Issues| Sunhokey Prusa i3

  314 views 10 comments 0 points Most recent by Repetier October 2016