Motor Control

• Weird Stepper Motor Behavior

  834 views 4 comments 0 points Most recent by Bishop November 2015
• Extruder no life :)

  202 views 6 comments 0 points Most recent by Repetier November 2015
• Double Distance after Back_on_home

  239 views 2 comments 0 points Most recent by Delta_88 October 2015
• Z Axis not working

  3.4K views 5 comments 0 points Most recent by Repetier October 2015
• X-axis homing has too large of a retraction

  275 views 2 comments 0 points Most recent by Repetier October 2015
• Extruder 1 and 2 Stepper Not Moving - Axteeg X3 Pro board

  241 views 1 comment 0 points Most recent by Repetier September 2015
• Z-probe Height vs Max z-probe bed dist in EEPROM Setting

  1.2K views 4 comments 0 points Most recent by briankb August 2015
• Assistance with autolevel on delta. process wont complete, errors in terminal about illegal values.

  456 views 12 comments 0 points Most recent by MShievitz August 2015
• Endstop triggers in only one direction?

  337 views 1 comment 0 points Most recent by Repetier August 2015
• X-motor homes in the wrong direction (Borlee A602)

  505 views 1 comment 0 points Most recent by Repetier August 2015
• Question about the additional Stepper Drivers feature

  198 views 1 comment 0 points Most recent by Repetier August 2015
• motors strain after any move command, printer homes accurately, but then motors disable

  117 views 0 comments 0 points Started by MShievitz July 2015
• Height Reduction Rostock

  271 views 3 comments 0 points Most recent by MShievitz July 2015
• Z axis will hold not move

  553 views 4 comments 0 points Most recent by browfingarf July 2015
• Extruder motor stop working during print

  800 views 9 comments 0 points Most recent by Repetier July 2015
• My X axis motor makes knocking noise

  275 views 4 comments 0 points Most recent by Tooluser June 2015
• While homing Optical End stops are triggered but steppers motors do not stop

  493 views 1 comment 0 points Most recent by Repetier June 2015
• Pick and Place

  105 views 1 comment 0 points Most recent by Repetier June 2015
• Is there a way to switch Axis in the firmware?

  363 views 1 comment 0 points Most recent by Repetier June 2015
• Z Axis Homing Problems

  618 views 1 comment 0 points Most recent by Repetier June 2015
• Help, maximum feedrate ??

  1.1K views 5 comments 0 points Most recent by Repetier May 2015
• PINS.H TOO LONG!!!

  231 views 6 comments 0 points Most recent by gmiller39 May 2015
• Aditional Motor Control

  412 views 5 comments 0 points Most recent by Repetier May 2015
• kossel in z direction moves double than the z value of manuel control in repetier-host.

  126 views 1 comment 0 points Most recent by Repetier May 2015
• Motors Not responding, Heater not Heating

  249 views 1 comment 0 points Most recent by Repetier May 2015
• Gear change; firmware fix?

  173 views 1 comment 0 points Most recent by Repetier May 2015
• Jerk in Dry run with delta-cable printer ignored

  320 views 2 comments 0 points Most recent by atair April 2015
• z axe move very slow

  714 views 1 comment 0 points Most recent by Repetier April 2015
• Steppers dont react on G code

  111 views 2 comments 0 points Most recent by EdV April 2015
• Z is only thing that won't work

  351 views 2 comments 0 points Most recent by soroban925 April 2015