Motor Control

• Z-Axis Erratic Behaviour

  1 view 4 comments 0 points Most recent by kptjrn June 19
• mks base v1.2 board with Y axis not working.

  1 view 2 comments 0 points Most recent by colin3d April 18
• All extruders working at the same time

  1 view 6 comments 0 points Most recent by Repetier April 4
• "Could not activate z" after trying to callibrate Z=0 and probe height on Sparkcube V1.1XL

  1 view 1 comment 0 points Most recent by bastelbude March 20
• Z Endsstop crashes into bed after pullup in right direction.

  1 view 7 comments 0 points Most recent by The_Maschinist March 5
• Z-Achse Configurieren

  1 view 1 comment 0 points Most recent by Repetier November 2023
• S-Curve Acceleration or Trapezoidal Acceleration

  1 view 3 comments 0 points Most recent by Repetier August 2023
• Motor is stuck and only humms loudly, will not home or move. M114/Move commands returns crazy value

  1 view 13 comments 0 points Most recent by Repetier May 2023
• G28 retracts too fast

  1 view 2 comments 0 points Most recent by Rick2 March 2023
• Is there a way to simulate the homed condition without motors and limits installed?

  1 view 3 comments 0 points Most recent by Repetier January 2023
• Can I add a feature to the firmware to send a message when motors have stopped?

  1 view 4 comments 0 points Most recent by Repetier January 2023
• ticking sounds

  1 view 6 comments 0 points Most recent by joule5 December 2022
• Durch Installation am haben sich beim Extruder Steps/mm verändert

  1 view 2 comments 0 points Most recent by Rotten00 October 2022
• CoreXY moved endstops 24.5mm on X and Y Min endstop bounce and Jitter

  1 view 2 comments 0 points Most recent by recoush September 2022
• setting up tmc2209 drivers in DEV2

  1 view 31 comments 0 points Most recent by Repetier March 2022
• Can anyone explain this Makergear M2 Z-axis movement.

  1 view 7 comments 0 points Most recent by Repetier February 2022
• The speed, acceleration and dimensions of the print area are not recorded in EPROM

  1 view 2 comments 0 points Most recent by Tenepopatam January 2022
• Mirrored motor on arduino mega and ramps to buildup a MPCNC

  1 view 4 comments 0 points Most recent by furfante December 2021
• motors just vibrate

  1 view 10 comments 0 points Most recent by Repetier December 2021
• All motors energized but not moving at all

  1 view 12 comments 0 points Most recent by gdville December 2021
• Unnecessary move during home

  1 view 2 comments 0 points Most recent by Repetier December 2021
• motor de-energizes

  1 view 10 comments 0 points Most recent by joule5 December 2021
• Home travelling in wrong direction regardless of Z_HOME_DIR

  1 view 2 comments 0 points Most recent by Stiofan November 2021
• Layer - Versatz in X+

  1 view 1 comment 0 points Most recent by Repetier November 2021
• Problema perdite asse x

  1 view 3 comments 0 points Most recent by Repetier August 2021
• Axes Real Position Feedback

  1 view 6 comments 0 points Most recent by TheClockwork August 2021
• Parametri Driver TMC2208

  1 view 3 comments 0 points Most recent by Repetier August 2021
• SLS printer motor control

  1 view 16 comments 0 points Most recent by Repetier June 2021
• I want to set up a motorized microscope with XYZ, 2 limits

  1 view 2 comments 0 points Most recent by Repetier May 2021
• Corexy does only run 1 motor

  1 view 4 comments 0 points Most recent by Repetier April 2021