Motor Control

• tman2020 need help

  1 view 1 comment 0 points Most recent by Repetier January 2020
• Slowing down when Endstop probing

  1 view 3 comments 0 points Most recent by Repetier January 2020
• Autobett Leveling CoreXY 1.0.4 DEV RADDS/DUE

  1 view 2 comments 0 points Most recent by Repetier January 2020
• Is it possible to use 3 Z steppers and also control them to do bed leveling ?

  1 view 4 comments 0 points Most recent by LUC January 2020
• G28 only Homes Z axis

  1 view 3 comments 0 points Most recent by PixelGl1tch December 2019
• End stop does not trigger after first homing

  1 view 24 comments 0 points Most recent by Rossini December 2019
• X2 motor doesn't move in IDEX

  1 view 12 comments 0 points Most recent by lmcbmai October 2019
• Rambo 1.4 Marlin Dual Endstop Repetier Host

  1 view 1 comment 0 points Most recent by Repetier October 2019
• Endstop for extramotor does not work

  1 view 26 comments 0 points Most recent by Repetier September 2019
• Mac OS and eeprom setting

  382 views 4 comments 0 points Most recent by Repetier September 2019
• G32 Error on Kossel (Delta)

  1 view 11 comments 0 points Most recent by Repetier August 2019
• TMC2209 - small movements after home?

  1 view 2 comments 0 points Most recent by MR_X June 2019
• Z axis jerky only driver gets very hot X Y are ok

  1 view 8 comments 0 points Most recent by lionellvp May 2019
• Always check endstops do not work with Probe

  1 view 1 comment 0 points Most recent by Repetier May 2019
• Y-Axis behaves like Z-Axis

  1 view 15 comments 0 points Most recent by Humbucker007 April 2019
• Custom Drive System

  214 views 8 comments 0 points Most recent by Repetier April 2019
• DRIVERS AND STEPS

  1 view 4 comments 0 points Most recent by mendelevium April 2019
• 3D Printer Z Axis Jamming

  1 view 1 comment 0 points Most recent by Repetier March 2019
• TMC 2130 Won`t Move- NEED HELP

  1 view 0 comments 0 points Started by mendelevium March 2019
• Homing problem

  1 view 2 comments 0 points Most recent by mendelevium March 2019
• z axis moves very slow

  1 view 1 comment 0 points Most recent by mivison March 2019
• Cable Robot using Repetier

  1 view 2 comments 0 points Most recent by Jagi February 2019
• Moving Manual Z in FW 1.0.3

  1 view 5 comments 0 points Most recent by batonio February 2019
• Problem with Z axis

  1 view 45 comments 0 points Most recent by MartinH January 2019
• Add reversing motor direction flag for mirrored axis steppers in next Release (MPCNC and similar)

  1 view 2 comments 0 points Most recent by LucidWolf January 2019
• problem with homming and manual control

  1 view 2 comments 0 points Most recent by baradov December 2018
• stepper not working

  1 view 2 comments 0 points Most recent by baradov December 2018
• Help Finding Drive for Stepper Motor

  76 views 1 comment 0 points Most recent by baradov December 2018
• Issues setting up dual Z axis steppers

  1 view 1 comment 0 points Most recent by MartinH December 2018
• Extruder motor won't run when plugged into E0

  1 view 5 comments 0 points Most recent by CSchiavoni November 2018