Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
Extruder & Bed
Extruder & Bed
«
1
2
3
4
5
6
7
…
17
»
Problem with heater in 2 extrusors
1
view
5
comments
0
points
Most recent by
ari
October 2019
2nd extruder work fine, 1st don't extrude.
1
view
6
comments
0
points
Most recent by
Zythum
October 2019
G-code to re-level bed, in between sequential prints.
1
view
5
comments
0
points
Most recent by
Repetier
September 2019
Dual extruder X Y offset
1
view
39
comments
0
points
Most recent by
klaus
September 2019
Extrududer decoupled and bed heating up for no reason
1
view
1
comment
0
points
Most recent by
Repetier
August 2019
Hotend cooling fan not turning on when heating extruder
1
view
11
comments
0
points
Most recent by
Pete
August 2019
Y-axis homing
1
view
2
comments
0
points
Most recent by
tomasby
August 2019
Extending the build plate (y axis)
1
view
3
comments
0
points
Most recent by
Repetier
August 2019
Setting different E-Steps when using Ditto mode
1
view
5
comments
0
points
Most recent by
Repetier
July 2019
Heater seems decoupled com thermistor
1
view
4
comments
0
points
Most recent by
sillass
June 2019
Filament out sensor
1
view
3
comments
0
points
Most recent by
Repetier
June 2019
Probleme Aufheizen Extruder 2
1
view
4
comments
0
points
Most recent by
silvkat
June 2019
Heater decoupled + PID autotune
1
view
6
comments
0
points
Most recent by
ChicoCybergoth
May 2019
Problems with dual extrusion using a wipe tower
1
view
1
comment
0
points
Most recent by
Repetier
May 2019
Z-Probe - Activating z-probe would lead to forbidden xy position - WHY??
1
view
2
comments
0
points
Most recent by
Kiddow
May 2019
while doing G32, it press on the bed at some points.
1
view
6
comments
0
points
Most recent by
BernieG
May 2019
Z-probe hight- software indiferent to changes
1
view
0
comments
0
points
Started by
Deugemo
April 2019
After PID tuning extruder still overshoots on temp.
1
view
5
comments
0
points
Most recent by
Repetier
April 2019
Setting extruder temperature more precisely
1
view
3
comments
0
points
Most recent by
Repetier
April 2019
Mirrored Extruder spins with Z on Home and Raise
1
view
10
comments
0
points
Most recent by
RandalZimmer
March 2019
Putting PID info into arduino sketch
1
view
1
comment
0
points
Most recent by
Repetier
February 2019
Moving probe Z-up is vey slow
1
view
6
comments
0
points
Most recent by
batonio
February 2019
Extruder Offset in Deltas
1
view
2
comments
0
points
Most recent by
Riodda
February 2019
Hotend is always 13°C to Hot
1
view
2
comments
0
points
Most recent by
Tig3rch3n
February 2019
zprobe Activity
1
view
3
comments
0
points
Most recent by
Repetier
February 2019
I installed a EV63D extruder clone, now it hangs too low on my Davinci 1.0 using repetier 0.92
1
view
1
comment
0
points
Most recent by
Repetier
February 2019
Bed leveling and homing w Z-min
1
view
7
comments
0
points
Most recent by
Repetier
February 2019
Installed a long extruder, now it hangs too low on my Davinci 1.0. How do I lower the bed home?
25
views
2
comments
0
points
Most recent by
sswandler
February 2019
Extruder dead-time temperature occasionally out of control
1
view
4
comments
0
points
Most recent by
screwtop
February 2019
MABL mit BL Touch
1
view
14
comments
0
points
Most recent by
Repetier
January 2019
«
1
2
3
4
5
6
7
…
17
»