Extruder & Bed

• Can you change the extruder heater output from 12v to 24v?

  1 view 4 comments 0 points Most recent by Repetier February 2022
• MABL und verzogenes Heizbett

  1 view 1 comment 0 points Most recent by Repetier February 2022
• Extruder Position at startup

  1 view 3 comments 0 points Most recent by Repetier November 2021
• My 3d Printer Heats up to correct temp then stops and cools down immediately

  75 views 4 comments 0 points Most recent by Repetier November 2021
• Issue after autotune 303. Temp drops big time when fans kick in.

  1 view 3 comments 0 points Most recent by Repetier September 2021
• Bauteillüfter Probleme

  1 view 2 comments 0 points Most recent by cosmowave September 2021
• Exruder motor just stops

  1 view 2 comments 0 points Most recent by Repetier May 2021
• TEMP_1_PIN through TEMP_4_PIN seem to be broken

  1 view 2 comments 0 points Most recent by Anteino May 2021
• Is there a way to enter distortion values manually in unrechable Z-Probing areas

  1 view 4 comments 0 points Most recent by Repetier May 2021
• DEV2: G30 / G32 z-probe height

  1 view 3 comments 0 points Most recent by Repetier April 2021
• Heater heat up but cannot reach to the temperature (2 to 5 degree below)

  1 view 15 comments 0 points Most recent by MartinH April 2021
• Suddenly Z probing does not work anymore

  1 view 3 comments 0 points Most recent by BernieG April 2021
• Colido Compact Extruder Head Temperature

  1 view 2 comments 0 points Most recent by Iain March 2021
• extruder direction reversed

  1 view 2 comments 0 points Most recent by Repetier March 2021
• Rostock Max: HE280 accelerometer z probe & filament runout sensors

  1 view 53 comments 0 points Most recent by few March 2021
• Temperature dips

  1 view 18 comments 0 points Most recent by Repetier February 2021
• Temperature in Repetier Host different from the internal temperature of the nozzle

  1 view 1 comment 0 points Most recent by Repetier December 2020
• Move cold extruder

  1 view 11 comments 0 points Most recent by sandro730 December 2020
• Use Heated Bed as Filament Dryer

  1 view 4 comments 0 points Most recent by few December 2020
• error:One heater seems decoupled from thermistor - disabling all for safety! Recv

  1 view 4 comments 0 points Most recent by user November 2020
• max extrusion length

  1 view 3 comments 0 points Most recent by Repetier November 2020
• wich settings for E3D PT1000 temp Sensor

  1 view 0 comments 0 points Started by asworx November 2020
• Extruder overhoots while heating up

  1 view 3 comments 0 points Most recent by Repetier October 2020
• BLTouch version compatibility

  1 view 1 comment 0 points Most recent by Repetier October 2020
• Cannot set firmware to control HEATER_2_PIN as extruder cooling

  1 view 3 comments 0 points Most recent by Repetier October 2020
• Autotuned Extruder Consistently Under Temp

  1 view 1 comment 0 points Most recent by Repetier October 2020
• Auto Pid tuning

  1 view 9 comments 0 points Most recent by druckich July 2020
• E3D Cyclops with Repetier Configuration

  1 view 3 comments 0 points Most recent by Repetier July 2020
• problems with the offset of the extruder

  1 view 1 comment 0 points Most recent by Repetier June 2020
• I got stuck in configuring a dual x carriage setup

  1 view 28 comments 0 points Most recent by Repetier June 2020