Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
Extruder & Bed
Extruder & Bed
«
1
2
3
4
5
6
7
…
16
»
(Extruder-) heating at very low temperatures (
1
view
3
comments
0
points
Most recent by
Repetier
December 2018
changing ext0_heater_pin not working.
1
view
1
comment
0
points
Most recent by
larry_h
December 2018
Mixing extruder - filament change problem
1
view
8
comments
0
points
Most recent by
jokejoke
December 2018
Not Able to Configure a 2-to-1 Mix/Switch Extruder
455
views
12
comments
0
points
Most recent by
Repetier
December 2018
Nozzle does not extrude filament
1
view
8
comments
0
points
Most recent by
RAyWB
November 2018
Firmware Retraction
1
view
2
comments
0
points
Most recent by
opy01
October 2018
Repetier-Firmware Does Not Recognize The Hotend on Ramps 1.4
1
view
1
comment
0
points
Most recent by
Deutadado
October 2018
Can not correct bed temp setting
1
view
1
comment
0
points
Most recent by
Repetier
October 2018
Bed leveling compensation error
1
view
4
comments
0
points
Most recent by
Repetier
October 2018
Heated bed zones
1
view
2
comments
0
points
Most recent by
Luca
October 2018
My extruder stepper motor will not work!!!
1
view
2
comments
0
points
Most recent by
Gwarden
October 2018
G30 is working but G32 S2 is not.
1
view
7
comments
0
points
Most recent by
Jonathan9573
October 2018
Mixing Extruder keine Reaktion FW1.0.2
1
view
3
comments
0
points
Most recent by
Doccos
September 2018
Second extruder (EXT1) is not working
1
view
2
comments
0
points
Most recent by
DanceM
September 2018
Invert PID for cooling
1
view
3
comments
0
points
Most recent by
Repetier
August 2018
Single point probing, to set Z before printing.
1
view
1
comment
0
points
Most recent by
Repetier
August 2018
Extruder 1 heizt schneller als Extruder 2
1
view
3
comments
0
points
Most recent by
Repetier
August 2018
Retraction Not Working
1
view
1
comment
0
points
Most recent by
LKLMMedia
August 2018
Confusing Z-Probe Settings
1
view
7
comments
0
points
Most recent by
Arnold
August 2018
Diamond Mixedcolor Extruders
1
view
2
comments
0
points
Most recent by
Repetier
August 2018
No power to extruder heater
1
view
3
comments
0
points
Most recent by
Repetier
August 2018
Z-homing with Z-Probe
1
view
1
comment
0
points
Most recent by
CatSailer1279
August 2018
Tronxy X3 Bed auto-level with Repetier Firmware
1
view
1
comment
0
points
Most recent by
AlphaBot
August 2018
how to extrude filiment along an axis?
1
view
2
comments
0
points
Most recent by
recoush
July 2018
HEATING IS OFF FROM SETTING
1
view
1
comment
0
points
Most recent by
Repetier
July 2018
Z Probe overriding Z min by M119?
1
view
0
comments
0
points
Started by
Xolotl
July 2018
Filament out sensor
1
view
5
comments
0
points
Most recent by
Repetier
June 2018
Hotend: Heater decoupled message, after finishing a print + setting new temp. (Wanhao i3, RAMPS 1.4
1
view
2
comments
0
points
Most recent by
Rejutka
May 2018
Tool Change Speed
1
view
12
comments
0
points
Most recent by
opy01
May 2018
How do I set up repetier firmware to know my bed is 27 mm away from my x limit switch?
1
view
5
comments
0
points
Most recent by
opy01
May 2018
«
1
2
3
4
5
6
7
…
16
»