Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
Extruder & Bed
Extruder & Bed
«
1
2
3
4
5
6
7
…
16
»
Problems with X axis while homing
1
view
1
comment
0
points
Most recent by
Repetier
April 2020
3 Extruder, alle an Jam Pin Y-min
1
view
6
comments
0
points
Most recent by
ziegelstein
April 2020
Parking extruders offsets issue
1
view
0
comments
0
points
Started by
Serenitas
April 2020
Jam detection help please
97
views
12
comments
0
points
Most recent by
furynick
April 2020
Auto bed leveling with inductive sensor
4.1K
views
17
comments
0
points
Most recent by
Repetier
April 2020
after update to 1.0.3 firmware , temp unstable
1
view
1
comment
0
points
Most recent by
Repetier
April 2020
Dual Extruder - Wipe and Prime tower using both filiments even when only one is needed. Support issu
1
view
2
comments
0
points
Most recent by
Ruskie
March 2020
Temperatur schwankt gleichmäßig um 5°
1
view
1
comment
0
points
Most recent by
Repetier
March 2020
Runout Sensor
1
view
1
comment
0
points
Most recent by
Repetier
March 2020
Thermistor in common ground
1
view
1
comment
0
points
Most recent by
ChicoCybergoth
February 2020
Bed Leveling using Z_PROBE_START_SCRIPT and Z_PROBE_FINISHED_SCRIPT: Multiple commands does not work
1
view
3
comments
0
points
Most recent by
good_idea
February 2020
HOTEND SICAKLIĞI
1
view
0
comments
0
points
Started by
black
February 2020
Best way to handle two distorsion maps
1
view
1
comment
0
points
Most recent by
Repetier
February 2020
Dual Extruder with fan control on MKS Base V1.4
1
view
3
comments
0
points
Most recent by
Repetier
January 2020
Bed Down after print finishes.
1
view
2
comments
0
points
Most recent by
JMcGraw47
January 2020
Firmware retraction not working as expected
1
view
2
comments
0
points
Most recent by
opy01
January 2020
checksum error mismatch
1
view
2
comments
0
points
Most recent by
pier
January 2020
New mains bed install - RADDS not turning on SSR
1
view
1
comment
0
points
Most recent by
ixlix
December 2019
Unexpected behavior when switching Tools in IDEX
1
view
0
comments
0
points
Started by
lmcbmai
October 2019
Problem with heater in 2 extrusors
1
view
5
comments
0
points
Most recent by
ari
October 2019
2nd extruder work fine, 1st don't extrude.
1
view
6
comments
0
points
Most recent by
Zythum
October 2019
G-code to re-level bed, in between sequential prints.
1
view
5
comments
0
points
Most recent by
Repetier
September 2019
Dual extruder X Y offset
1
view
39
comments
0
points
Most recent by
klaus
September 2019
Extrududer decoupled and bed heating up for no reason
1
view
1
comment
0
points
Most recent by
Repetier
August 2019
Hotend cooling fan not turning on when heating extruder
1
view
11
comments
0
points
Most recent by
Pete
August 2019
Y-axis homing
1
view
2
comments
0
points
Most recent by
tomasby
August 2019
Extending the build plate (y axis)
1
view
3
comments
0
points
Most recent by
Repetier
August 2019
Setting different E-Steps when using Ditto mode
1
view
5
comments
0
points
Most recent by
Repetier
July 2019
Heater seems decoupled com thermistor
1
view
4
comments
0
points
Most recent by
sillass
June 2019
Filament out sensor
1
view
3
comments
0
points
Most recent by
Repetier
June 2019
«
1
2
3
4
5
6
7
…
16
»