Extruder & Bed

• Extruder temperature not stable,changing in a range about 14 °C

  1 view 5 comments 0 points Most recent by raymond January 2018
• Extruder offsets

  1 view 17 comments 0 points Most recent by Repetier January 2018
• Temperature issue Thermistors?

  1 view 1 comment 0 points Most recent by Repetier December 2017
• Issues bed levelling

  1 view 58 comments 0 points Most recent by Repetier December 2017
• CNC - Bed Leveling

  1 view 3 comments 0 points Most recent by Repetier December 2017
• Autobedlevel and Z_PROBE_HEIGHT

  1 view 5 comments 0 points Most recent by Repetier December 2017
• Extruder Motor Skipping Each Half Revolution

  1 view 3 comments 0 points Most recent by Repetier December 2017
• Extruder heater not providing enough heat

  1 view 3 comments 0 points Most recent by MartinH December 2017
• PID frequency for SSR

  1 view 7 comments 0 points Most recent by Repetier December 2017
• Need to slowly heat up the bed not to break the glass - is it possible?

  1 view 2 comments 0 points Most recent by good_idea December 2017
• Hot end not getting any current

  1 view 1 comment 0 points Most recent by Repetier November 2017
• Baby stepping after g32 and changing zmax

  18 views 1 comment 0 points Most recent by Repetier November 2017
• Dual Print Cooling Fans

  36 views 3 comments 0 points Most recent by Repetier November 2017
• Problems with autoleveling and homing

  60 views 4 comments 0 points Most recent by Timppa71 November 2017
• speed FILAMENTCHANGE

  41 views 4 comments 0 points Most recent by Repetier October 2017
• Fatal error on autiolevel

  22 views 1 comment 0 points Most recent by Repetier October 2017
• Extruder don't turn anyway (two extruders) and second hotend is dead

  60 views 5 comments 0 points Most recent by MadCat October 2017
• X axis issue.

  38 views 3 comments 0 points Most recent by Repetier October 2017
• Z leveling with probe mysteries ?????

  105 views 13 comments 0 points Most recent by BernieG October 2017
• autoleveling adjusting zprobeheight

  117 views 7 comments 0 points Most recent by Repetier September 2017
• printing not smooth more like pin heads.

  33 views 2 comments 0 points Most recent by recoush September 2017
• Bed: M303 E-1 S60 C8 Is this command working in Repetier at all?

  35 views 1 comment 0 points Most recent by Repetier September 2017
• Heated bed temp drops when print starts

  150 views 24 comments 0 points Most recent by Sewyboowy September 2017
• Extruder & Bed not heating

  68 views 5 comments 0 points Most recent by RAyWB September 2017
• mirror imaging of printing words

  53 views 9 comments 0 points Most recent by recoush September 2017
• duial extruder iis hitting table

  63 views 7 comments 0 points Most recent by recoush September 2017
• Autolevel - Z axis crashes into bed!!

  170 views 14 comments 0 points Most recent by recoush August 2017
• Pin D9 and D8 are tied together and I dont know why

  37 views 2 comments 0 points Most recent by Repetier August 2017
• Extruder and motors tripping fuse

  23 views 0 comments 0 points Started by mitch25 August 2017
• E3D Volcano loosing temp then trips out

  15 views 1 comment 0 points Most recent by Repetier August 2017