Extruder & Bed

• How do I get auto bed levelling to use the method that I set up?

  92 views 1 comment 0 points Most recent by Repetier February 2017
• Can't complete Bed PID autotune

  390 views 1 comment 0 points Most recent by Repetier February 2017
• Settings Extruder X_Offset & Y_Offset

  152 views 6 comments 0 points Most recent by Tanuki44 February 2017
• Extracting existing temp tables from firmware

  136 views 8 comments 0 points Most recent by YP3002T January 2017
• Is it possible to disable/enable heated bed without reflash firmware?

  103 views 3 comments 0 points Most recent by MartinH January 2017
• X and Y offset in firmware

  1.9K views 3 comments 0 points Most recent by Repetier January 2017
• Anet A8 Extruder and heat bed not working

  182 views 1 comment 0 points Most recent by Repetier January 2017
• Dual Extrusion_the parts doesn't assembly each other

  45 views 1 comment 0 points Most recent by Repetier January 2017
• Zprobing with Kossel "allen key" type probe

  39 views 1 comment 0 points Most recent by RhinoRap January 2017
• E3D PT-100 on RADDS configuration

  311 views 10 comments 0 points Most recent by Rossini January 2017
• Ramps 1.4 strange temperature behavior

  59 views 2 comments 0 points Most recent by snorg January 2017
• Prusa i3 ramps 1.4 , min endstops only - z printing offset magicaly is active

  104 views 8 comments 0 points Most recent by MartinH January 2017
• Removable Z-Probe Height and Bed Leveling

  81 views 0 comments 0 points Started by tcurdt January 2017
• Extruder offset setting question

  80 views 2 comments 0 points Most recent by m.marino January 2017
• G32 crashing on negative X position

  95 views 9 comments 0 points Most recent by Repetier January 2017
• Mixing extruder: purging problems

  78 views 2 comments 0 points Most recent by kileitza January 2017
• "Z Probe did not untrigger" error

  73 views 3 comments 0 points Most recent by MartinH January 2017
• SparkCube CoreXY with Auto Bed Leveling XY-Offset error (possible Bug?)

  151 views 8 comments 0 points Most recent by carstenwalther January 2017
• Extruder retracts the filament out of hotend

  137 views 10 comments 0 points Most recent by Repetier January 2017
• Extruder heats up on its own and continues to heat up

  79 views 4 comments 0 points Most recent by unknown28 January 2017
• Auto-level and Z- zero position

  107 views 1 comment 0 points Most recent by matthewsjl January 2017
• Reset auto level matrix

  169 views 1 comment 0 points Most recent by Repetier January 2017
• Dual Extruder with single work cooling fan

  111 views 4 comments 0 points Most recent by Bumble January 2017
• Z probe config ?

  253 views 3 comments 0 points Most recent by Repetier January 2017
• Extruder not moving - but is tested OK - how to swap from E0 to E1?

  114 views 5 comments 0 points Most recent by MartinH December 2016
• Manual Distortion Map Input

  105 views 3 comments 0 points Most recent by Repetier December 2016
• Extruder temp decreasing then decoupled during long print

  68 views 2 comments 0 points Most recent by pefozzy December 2016
• Hot End fails to reach temp during print job, but works fine manually

  100 views 3 comments 0 points Most recent by hammertongs December 2016
• Probe Preventing Z Height Adjustment settings

  144 views 3 comments 0 points Most recent by AlbertZeroK December 2016
• g32 s2 misconfig?

  382 views 33 comments 0 points Most recent by Repetier December 2016