Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Firmware
›
Extruder & Bed
Extruder & Bed
«
1
2
3
4
5
6
7
…
14
»
New mains bed install - RADDS not turning on SSR
1
view
1
comment
0
points
Most recent by
ixlix
December 4
Unexpected behavior when switching Tools in IDEX
1
view
0
comments
0
points
Started by
lmcbmai
October 26
Problem with heater in 2 extrusors
1
view
5
comments
0
points
Most recent by
ari
October 26
2nd extruder work fine, 1st don't extrude.
1
view
6
comments
0
points
Most recent by
Zythum
October 1
G-code to re-level bed, in between sequential prints.
1
view
5
comments
0
points
Most recent by
Repetier
September 29
Dual extruder X Y offset
1
view
39
comments
0
points
Most recent by
klaus
September 23
Extrududer decoupled and bed heating up for no reason
1
view
1
comment
0
points
Most recent by
Repetier
August 15
Hotend cooling fan not turning on when heating extruder
1
view
11
comments
0
points
Most recent by
Pete
August 15
Y-axis homing
1
view
2
comments
0
points
Most recent by
tomasby
August 14
Extending the build plate (y axis)
1
view
3
comments
0
points
Most recent by
Repetier
August 8
Setting different E-Steps when using Ditto mode
1
view
5
comments
0
points
Most recent by
Repetier
July 6
Heater seems decoupled com thermistor
1
view
4
comments
0
points
Most recent by
sillass
June 28
Filament out sensor
1
view
3
comments
0
points
Most recent by
Repetier
June 22
Probleme Aufheizen Extruder 2
1
view
4
comments
0
points
Most recent by
silvkat
June 1
Heater decoupled + PID autotune
1
view
6
comments
0
points
Most recent by
ChicoCybergoth
May 31
Problems with dual extrusion using a wipe tower
1
view
1
comment
0
points
Most recent by
Repetier
May 29
Z-Probe - Activating z-probe would lead to forbidden xy position - WHY??
1
view
2
comments
0
points
Most recent by
Kiddow
May 28
while doing G32, it press on the bed at some points.
1
view
6
comments
0
points
Most recent by
BernieG
May 3
Z-probe hight- software indiferent to changes
1
view
0
comments
0
points
Started by
Deugemo
April 22
After PID tuning extruder still overshoots on temp.
1
view
5
comments
0
points
Most recent by
Repetier
April 9
Setting extruder temperature more precisely
1
view
3
comments
0
points
Most recent by
Repetier
April 8
Mirrored Extruder spins with Z on Home and Raise
1
view
10
comments
0
points
Most recent by
RandalZimmer
March 12
Putting PID info into arduino sketch
1
view
1
comment
0
points
Most recent by
Repetier
February 27
Moving probe Z-up is vey slow
1
view
6
comments
0
points
Most recent by
batonio
February 18
Extruder Offset in Deltas
1
view
2
comments
0
points
Most recent by
Riodda
February 16
Hotend is always 13°C to Hot
1
view
2
comments
0
points
Most recent by
Tig3rch3n
February 12
zprobe Activity
1
view
3
comments
0
points
Most recent by
Repetier
February 10
I installed a EV63D extruder clone, now it hangs too low on my Davinci 1.0 using repetier 0.92
1
view
1
comment
0
points
Most recent by
Repetier
February 7
Bed leveling and homing w Z-min
1
view
7
comments
0
points
Most recent by
Repetier
February 6
Installed a long extruder, now it hangs too low on my Davinci 1.0. How do I lower the bed home?
25
views
2
comments
0
points
Most recent by
sswandler
February 6
«
1
2
3
4
5
6
7
…
14
»