Extruder & Bed

• Z-homing with Z-Probe

  1 view 1 comment 0 points Most recent by CatSailer1279 August 2018
• Tronxy X3 Bed auto-level with Repetier Firmware

  1 view 1 comment 0 points Most recent by AlphaBot August 2018
• how to extrude filiment along an axis?

  1 view 2 comments 0 points Most recent by recoush July 2018
• HEATING IS OFF FROM SETTING

  1 view 1 comment 0 points Most recent by Repetier July 2018
• Z Probe overriding Z min by M119?

  1 view 0 comments 0 points Started by Xolotl July 2018
• Filament out sensor

  1 view 5 comments 0 points Most recent by Repetier June 2018
• Hotend: Heater decoupled message, after finishing a print + setting new temp. (Wanhao i3, RAMPS 1.4

  1 view 2 comments 0 points Most recent by Rejutka May 2018
• Tool Change Speed

  1 view 12 comments 0 points Most recent by opy01 May 2018
• How do I set up repetier firmware to know my bed is 27 mm away from my x limit switch?

  1 view 5 comments 0 points Most recent by opy01 May 2018
• E3D Cyclops configuration in 1.0.2

  1 view 3 comments 0 points Most recent by Repetier April 2018
• New setup Z homing crashes into bed

  1 view 25 comments 0 points Most recent by opy01 April 2018
• Non-mixing 3-in-1-out extruder

  1 view 12 comments 0 points Most recent by CatSailer1279 April 2018
• Extruding not retracting

  243 views 3 comments 0 points Most recent by m3evo April 2018
• Bed Correction with three motors - little error left

  1 view 8 comments 0 points Most recent by Repetier March 2018
• Is it possible to command servo/extruder in g-code with tool change

  1 view 5 comments 0 points Most recent by keesv March 2018
• Homing Z with probe

  103 views 2 comments 0 points Most recent by erik23 March 2018
• Semi automatic bed leveling

  1 view 3 comments 0 points Most recent by Repetier February 2018
• Changing minimum extruder temperature to 27°C / 80.6°F

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Homing puts Z through max value

  1 view 1 comment 0 points Most recent by Repetier February 2018
• EPCOS 100K Thermistor (B57560G1104F) not work at all

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Problem printing with extruder 2 only

  1 view 8 comments 0 points Most recent by Kamikazer2 February 2018
• Auto level + Distortion correct setup

  1 view 0 comments 0 points Started by florin42 January 2018
• Problem with Dyze 500C hot end not extruding

  1 view 1 comment 0 points Most recent by Twmaster January 2018
• Enable an endstop to trigger a pause for a syringe extruder

  1 view 1 comment 0 points Most recent by Lauhaus January 2018
• Correct Setup of Dual Extruder with BLTouch Autobedleveling

  1 view 0 comments 0 points Started by MrZortrax January 2018
• Custom retract routine with a servo

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Repetier loosing connection everytime i click print!

  1 view 1 comment 0 points Most recent by Repetier January 2018
• Situation with extruder

  1 view 1 comment 0 points Most recent by Repetier January 2018
• fts sensor error

  1 view 3 comments 0 points Most recent by Repetier January 2018
• Heat heats slowly after emergency stop and reset with M999

  1 view 3 comments 0 points Most recent by Repetier January 2018