Extruder & Bed

• slicer extrusion g code

  73 views 9 comments 0 points Most recent by recoush August 2017
• How to undo autotune

  31 views 1 comment 0 points Most recent by Repetier August 2017
• Autoleveling error, Nozzle scratches the bed

  87 views 10 comments 0 points Most recent by Repetier August 2017
• Under Extrusion after a retract

  89 views 5 comments 0 points Most recent by Repetier August 2017
• Arduino Lockup

  30 views 3 comments 0 points Most recent by 3DBOT August 2017
• Extruder Stepper is not working!

  2K views 15 comments 0 points Most recent by hokanp August 2017
• extruding around the X and Y perimeter

  15 views 0 comments 0 points Started by recoush August 2017
• Radds + 2x Adafruit AD8495 Breakout + NTCS0603E3104FXT

  145 views 21 comments 0 points Most recent by Repetier August 2017
• bowden v6 extrusion calibration

  50 views 3 comments 0 points Most recent by recoush August 2017
• Temperature always 500 using Max6675

  40 views 2 comments 0 points Most recent by jszxwcq August 2017
• Ditto printing/Mixing Extruder

  52 views 2 comments 0 points Most recent by Vizaresh August 2017
• Anet A8 extruder thermo-sensor settings

  142 views 10 comments 0 points Most recent by Flid August 2017
• extruder type cyclope

  38 views 0 comments 0 points Started by roland42 August 2017
• autolevel

  197 views 10 comments 0 points Most recent by roland42 August 2017
• Changed Processer ID?

  22 views 3 comments 0 points Most recent by Repetier July 2017
• Shared power "budget" for extruder and bed

  77 views 6 comments 0 points Most recent by mpl July 2017
• Heater Extruder 0 D10 used for a magnet: how to reduce power after 1s?

  55 views 9 comments 0 points Most recent by Repetier July 2017
• Extrusion when moving on axis

  63 views 7 comments 0 points Most recent by robinsonjas July 2017
• How to criate new presets of temperature?

  31 views 1 comment 0 points Most recent by Repetier July 2017
• Syringe Pump Extruder

  30 views 0 comments 0 points Started by GaryB July 2017
• Problem with the displacement of the inductive sensor to the nozzle

  45 views 2 comments 0 points Most recent by derschutzhund July 2017
• Overextruding

  143 views 13 comments 0 points Most recent by topedesigns July 2017
• Enhancement request - Adjustable extruder 'jerk' setting?

  67 views 6 comments 0 points Most recent by RGN01 June 2017
• Extruder not working after Cura upgrade

  72 views 3 comments 0 points Most recent by Repetier June 2017
• jam detection only as limit swith

  37 views 1 comment 0 points Most recent by Repetier May 2017
• 3d printer extruder is off will not turn on.

  42 views 2 comments 0 points Most recent by oldfart May 2017
• G33 produces error messages and runs out of bed borders

  138 views 15 comments 0 points Most recent by reid60 May 2017
• Operating a Shared Extruder with a Y-switch Between Steppers and Hotend

  191 views 27 comments 0 points Most recent by Doug40 May 2017
• My hot end suddenly stops heating and decouples

  186 views 5 comments 0 points Most recent by gassiebernal May 2017
• X0 position after G29

  65 views 3 comments 0 points Most recent by ClaudioP April 2017