Extruder & Bed

• g32 s2 misconfig?

  382 views 33 comments 0 points Most recent by Repetier December 2016
• Mixing extruder + extruder for support-material. Is it possible with repetier firmware?

  93 views 2 comments 0 points Most recent by kileitza December 2016
• Could not reach temperature anymore after changing configuration

  51 views 1 comment 0 points Most recent by Repetier December 2016
• Multifilament extruder switching

  236 views 4 comments 0 points Most recent by Simme December 2016
• mess alignment issue

  28 views 2 comments 0 points Most recent by t4h3r December 2016
• Extuder Heating problem

  143 views 10 comments 0 points Most recent by t4h3r December 2016
• Securitiy Switch for the Heatbed with a Relay

  73 views 5 comments 0 points Most recent by Repetier December 2016
• Autobedlevelling with 0.92.9

  197 views 11 comments 0 points Most recent by Repetier December 2016
• Dual extruder but only one move

  66 views 2 comments 0 points Most recent by raymond November 2016
• clogged extruder

  78 views 3 comments 0 points Most recent by Repetier November 2016
• PID Autotune not working on second extruder

  167 views 2 comments 0 points Most recent by strips November 2016
• HeyMy extrude Motor is Not working..

  113 views 5 comments 0 points Most recent by Repetier November 2016
• Semitec 104 GT-2 wrong temperature

  59 views 1 comment 0 points Most recent by Repetier November 2016
• Thermistor E3D v6 displays wrong value

  235 views 1 comment 0 points Most recent by Repetier November 2016
• what changes in the configuration are necessary to use 2 extruder?

  51 views 2 comments 0 points Most recent by Metalhead November 2016
• G32 vs G33

  339 views 6 comments 0 points Most recent by shaiss November 2016
• Heatbed Too Slow Heating

  168 views 1 comment 0 points Most recent by Repetier October 2016
• Z-height, Z-Min and Z-probe setup questions

  3.5K views 9 comments 0 points Most recent by Repetier October 2016
• More than 16 virtual extruders? Eeprom positions?

  110 views 2 comments 0 points Most recent by rhklein October 2016
• Hoo to set a PTC thermistore "PT1000" ?

  96 views 7 comments 0 points Most recent by ludo October 2016
• Radds + 0.92.9 + MAX6675 Thermocouple

  64 views 0 comments 0 points Started by Couture619 October 2016
• Disabling in Configuration.h DECOUPLE_TEST ????

  109 views 4 comments 0 points Most recent by batonio October 2016
• How to tilt Chimera Hot End so Second Nozzle doesnt Collide with the printed Part? (Offset)

  151 views 1 comment 0 points Most recent by Repetier September 2016
• Add Choice in LCD Menu

  125 views 2 comments 0 points Most recent by Tanuki44 September 2016
• Hotend and bed thermistors crazy values

  111 views 3 comments 0 points Most recent by Repetier September 2016
• "Error:One heater seems decoupled from thermistor - disabling all for safety" no hardware issue

  188 views 1 comment 0 points Most recent by Repetier September 2016
• Cooler Fun on Melzi (wanhao i3) switched earlier than specified in the gcode

  55 views 1 comment 0 points Most recent by Repetier September 2016
• cant make the extruder or bed to heat

  172 views 4 comments 0 points Most recent by Repetier September 2016
• Any possibility to read out temperature of Thermo coupled PWM fan?

  68 views 2 comments 0 points Most recent by docpayce August 2016
• Extruder not feeding correctly

  418 views 10 comments 0 points Most recent by Repetier August 2016