Extruder & Bed

• Rambo board, extending and retracting Z probe with servo

  180 views 3 comments 0 points Most recent by Repetier May 2016
• Fan confusion - RAMBo

  179 views 1 comment 0 points Most recent by Repetier May 2016
• 'Repetier-Firmware Configuration Tool' resetting my Extruders temp sensor

  303 views 1 comment 0 points Most recent by AK_Eric May 2016
• Extruder won't heat up after i hit print.... extruder works in manual mode.... (slic3r&Repetier)

  114 views 0 comments 0 points Started by Slapjack14NL April 2016
• extruder not powering on in manual control

  281 views 4 comments 0 points Most recent by RAyWB April 2016
• Oval Printing after Correction Diagonal A,B,C in EEPROM

  117 views 2 comments 0 points Most recent by Repetier April 2016
• Bed Overheats from SD Card, Works perfectly from Repetier Host

  219 views 8 comments 0 points Most recent by 3didd April 2016
• in 0.91 heat bed works, in 0.92.9 it doesn't

  147 views 2 comments 0 points Most recent by totosse April 2016
• Custom bed without heat won't allow for auto adjust

  109 views 3 comments 0 points Most recent by Repetier April 2016
• Extruder extrudes during retraction

  279 views 5 comments 0 points Most recent by Repetier April 2016
• Output Extruder

  193 views 2 comments 0 points Most recent by abpccpba April 2016
• Calibration/BedLevel

  966 views 14 comments 0 points Most recent by SametAyhan April 2016
• Waveform on shell of printed.

  74 views 1 comment 0 points Most recent by Repetier April 2016
• Heat Bed Won't Turn On

  395 views 1 comment 0 points Most recent by Repetier April 2016
• Diamond nozzle not heating up, unless...

  253 views 5 comments 0 points Most recent by justTrying March 2016
• The Z-Probe ran fine but impact with my glass when print!

  474 views 8 comments 0 points Most recent by fanofcc March 2016
• Extruder motor issue on Delta

  790 views 29 comments 0 points Most recent by Roko March 2016
• Extruder won't move (3 mixing Extruder)

  229 views 6 comments 0 points Most recent by Paxy March 2016
• 3rd extruder issue

  144 views 2 comments 0 points Most recent by Paxy March 2016
• X Y Offset

  216 views 0 comments 0 points Started by NFAZ10 March 2016
• Z-Height not moving with Auto leveling

  155 views 2 comments 0 points Most recent by arzhurp March 2016
• How to access EEPROM autolevel data?

  109 views 0 comments 0 points Started by Hecot March 2016
• Why configuration between first extruder and second extruder is different?

  161 views 8 comments 0 points Most recent by yanie_karlina March 2016
• Is it possible to print as Ordinary dual colour but only retract together

  96 views 1 comment 0 points Most recent by Huhn February 2016
• Z probe switch logic.

  211 views 3 comments 0 points Most recent by Repetier February 2016
• 8 Extruders supported?

  87 views 1 comment 0 points Most recent by Repetier February 2016
• Heat bed and extruder in reverse?

  131 views 1 comment 0 points Most recent by Tdog February 2016
• No extrusion from second extruder

  237 views 4 comments 0 points Most recent by robertalpha February 2016
• Z motors for bed leveling

  164 views 3 comments 0 points Most recent by Repetier February 2016
• heating up bed: Command M140 SXX - heating fails after 1s; Command M190 SXX works properly

  311 views 16 comments 0 points Most recent by Repetier February 2016