Extruder & Bed

• Repetier FW + Simplify3D + Diamond hotend + FW retraction

  386 views 1 comment 0 points Most recent by Repetier August 2016
• Dead Time Control

  194 views 1 comment 0 points Most recent by Repetier August 2016
• Extruding too fast

  186 views 3 comments 0 points Most recent by Repetier August 2016
• Delta bed cupped - Need to manually adjust it out.

  81 views 4 comments 0 points Most recent by Taxus812 August 2016
• How to set up Diamond triple-filament single-nozzle mixing extruder on Rumba board

  4.9K views 4 comments 0 points Most recent by Repetier August 2016
• Diamond Hotend (3 extruder) and Repetier firmware

  750 views 3 comments 0 points Most recent by Repetier August 2016
• Z probe... How to define the 3 Points?

  127 views 5 comments 0 points Most recent by Repetier August 2016
• Extruder won't heat up to more than 185 degrees with PID control

  269 views 8 comments 0 points Most recent by Repetier August 2016
• Re Position the new extruder to the bed

  146 views 1 comment 0 points Most recent by lucpet August 2016
• Azteeg X3 PRO - Problems with third (..forth, fifth..) extruder

  247 views 14 comments 0 points Most recent by Repetier July 2016
• tmp007 IR sensor on repetier firmware??

  116 views 3 comments 0 points Most recent by Repetier July 2016
• 1.0dev shoots too much filament

  79 views 1 comment 0 points Most recent by Repetier July 2016
• heating bed problem

  101 views 3 comments 0 points Most recent by Repetier July 2016
• Z probe not Working

  306 views 3 comments 0 points Most recent by Getget July 2016
• Cooling fan constantly runs even when extruder is at room temp

  229 views 1 comment 0 points Most recent by Repetier July 2016
• New Z probing Design(temporarily disable endstop)

  218 views 2 comments 0 points Most recent by DannyGh July 2016
• Z-test measures properly. but wrong track

  75 views 1 comment 0 points Most recent by Repetier July 2016
• Printer running over Endstops

  92 views 5 comments 0 points Most recent by Repetier July 2016
• Extruder going too high while probing

  125 views 3 comments 0 points Most recent by Repetier July 2016
• Mixing Nozzle / different steps per mm

  322 views 8 comments 0 points Most recent by Janosch June 2016
• Zprobed G32 makes zero Z to be 2mm above from bed. Z-probe height is measured with G30.

  255 views 4 comments 0 points Most recent by Repetier June 2016
• strange head motion...

  111 views 6 comments 0 points Most recent by madarren June 2016
• Ultimaker, inductive probe and both Z endstops

  122 views 0 comments 0 points Started by mcexperts June 2016
• Z-Probing error

  170 views 1 comment 0 points Most recent by Repetier June 2016
• Change X, Y offset by GCODE

  315 views 3 comments 0 points Most recent by Repetier June 2016
• Z_PROBE_Y_OFFSET Ignored by G29/G32 but OK in Bed height map

  338 views 9 comments 0 points Most recent by deZeus June 2016
• G33 correction grid z-offset

  166 views 1 comment 0 points Most recent by Repetier May 2016
• New Feature Request ? Or is implemented

  245 views 4 comments 0 points Most recent by batonio May 2016
• Diamond Head / Cyclops Hotend - Mixing Head Extruder > 1 Not Working

  717 views 9 comments 0 points Most recent by Eddiie May 2016
• Dual extruder weirdeness

  144 views 0 comments 0 points Started by byarcand May 2016