Extruder & Bed

• Autolevel Renkforce RF1000

  310 views 1 comment 0 points Most recent by Repetier October 2015
• Height map - First and last meadure always give false reading

  260 views 6 comments 0 points Most recent by Repetier October 2015
• failing to compile - extruder z-offset error

  264 views 3 comments 0 points Most recent by Repetier September 2015
• Autoleveling

  1.1K views 17 comments 0 points Most recent by LouGeezer September 2015
• M323 unkown command and more autolevel mysteries

  216 views 3 comments 0 points Most recent by Repetier September 2015
• Autolevel ignores z probe

  232 views 4 comments 0 points Most recent by Sungod3k September 2015
• Extruder motor goes crazy

  293 views 2 comments 0 points Most recent by Repetier September 2015
• Thermocouple with AD579 chip on a Megatronics V3

  423 views 2 comments 0 points Most recent by chaoscrack August 2015
• (a lot of) autolevel issues

  1.3K views 9 comments 0 points Most recent by Repetier August 2015
• Function call to move extruder motor?

  172 views 1 comment 0 points Most recent by Repetier August 2015
• Extra extrusion on travel needed?

  243 views 6 comments 0 points Most recent by LouGeezer August 2015
• How to use D9 as print fan with Mixing extruder?

  276 views 1 comment 0 points Most recent by Repetier August 2015
• How to duplicate the extruder movement through the i2c?

  276 views 2 comments 0 points Most recent by Snipermand July 2015
• How to disable decoupling test?

  690 views 7 comments 0 points Most recent by Repetier July 2015
• Extruder/bed not heating up with new install

  638 views 3 comments 0 points Most recent by VDfreesince1983 July 2015
• Extruder and Bed not heating

  393 views 2 comments 0 points Most recent by Repetier July 2015
• New Thermistor displaying above actual tempature

  333 views 3 comments 0 points Most recent by Repetier July 2015
• Group Delete?

  65 views 1 comment 0 points Most recent by Repetier July 2015
• How to set DualExtruder up with Ramps 1.4

  370 views 2 comments 0 points Most recent by Tapps July 2015
• Need to Use E2 Heater

  334 views 1 comment 0 points Most recent by Repetier June 2015
• Z probe measurings points

  263 views 5 comments 0 points Most recent by Repetier June 2015
• bed leveling routine problem

  254 views 3 comments 0 points Most recent by Repetier June 2015
• Z probe does't measure using G32

  688 views 10 comments 0 points Most recent by Repetier June 2015
• Extruder 3 & 4 - EXT_Motors will not turn (0.92 Latest)

  1.1K views 7 comments 0 points Most recent by Repetier June 2015
• Extruder heating up but never stops till error

  225 views 4 comments 0 points Most recent by Repetier June 2015
• Is there a complete step by step manual for building Z probe

  3.6K views 15 comments 0 points Most recent by Repetier June 2015
• z-probe offset and extruder(s) offset for auto-leveling

  4.2K views 21 comments 0 points Most recent by Repetier May 2015
• Extruder not heating up

  3.5K views 1 comment 0 points Most recent by Repetier May 2015
• G29 crash my delta !!!

  501 views 1 comment 0 points Most recent by Repetier May 2015
• Extruder works but doesn't...

  231 views 1 comment 0 points Most recent by Repetier April 2015