Recent Discussions

• 2FA hinzufügen

  1 view 1 comment 0 points Most recent by Repetier_Support December 2021Repetier-Server
• Switch printer + light if G-Code is sent to printer

  1 view 3 comments 0 points Most recent by Repetier_Support December 2021Questions & Answers
• Connecting to a printer via tcp/ip

  1 view 1 comment 0 points Most recent by Repetier_Support December 2021Questions & Answers
• Setup - Raise3D E2 idex

  1 view 3 comments 0 points Most recent by modiug December 2021Questions & Answers
• zhoming with radds + arduino2 + bltouch

  1 view 2 comments 0 points Most recent by furfante December 2021Questions & Answers
• X axis randomly stops near top of prints. Happens on multiple printers randomly.

  1 view 5 comments 0 points Most recent by ryane3p December 2021Repetier-Server
• Klipper Firmware integration

  1 view 26 comments 0 points Most recent by Marco67 December 2021Feature Requests
• Server Migration

  1 view 1 comment 0 points Most recent by Repetier December 2021Questions & Answers
• Fernzugriff übers Internet

  1 view 5 comments 0 points Most recent by nosnbora December 2021Repetier-Server
• Add an option for Tree Support

  1 view 2 comments 0 points Most recent by MrAlvin December 2021Feature Requests
• Where to find the "search " function on the page?

  1 view 2 comments 0 points Most recent by LH4PI December 2021General
• Falsche Höhe nach G28 mit BLTouch

  1 view 7 comments 0 points Most recent by eiche2001de December 2021Repetier-Server
• Drucker bleibt bei längere drucken immer wieder stehen mit eingeschalteten Heizungen

  1 view 10 comments 0 points Most recent by Repetier December 2021Repetier-Server
• Keine Verbindung zum Raspi Zero 2W mit Repetier Image V28 über SSH oder Putty

  1 view 12 comments 0 points Most recent by Repetier December 2021Repetier-Server
• DHCP partially not working

  1 view 1 comment 0 points Most recent by Repetier December 2021Questions & Answers
• Deactivate the License

  1 view 1 comment 0 points Most recent by Repetier December 2021General
• Autoupdate to1.2.0

  1 view 1 comment 0 points Most recent by Repetier December 2021General
• Printer display disabled y Server

  1 view 10 comments 0 points Most recent by stafford December 2021Questions & Answers
• AP Modus

  1 view 4 comments 0 points Most recent by timoschuett December 2021Questions & Answers
• Wlan bricht ab / Webcam ohne funktion

  1 view 7 comments 0 points Most recent by Repetier December 2021Repetier-Server
• Unnecessary move during home

  1 view 2 comments 0 points Most recent by Repetier December 2021Motor Control
• disable jam detection

  1 view 0 comments 0 points Started by joule5 December 2021 Repetier-Firmware
• motor de-energizes

  1 view 10 comments 0 points Most recent by joule5 December 2021Motor Control
• Printer makes one move at a time after working fine

  1 view 1 comment 0 points Most recent by Repetier December 2021Repetier-Host
• Dashboard: Larger Webcam display.

  1 view 3 comments 0 points Most recent by SonjaDCUSA December 2021Questions & Answers
• Downgrade möglich?

  1 view 8 comments 0 points Most recent by Repetier December 2021Repetier-Server
• Druck bleibt Stehen

  1 view 1 comment 0 points Most recent by Repetier December 2021General
• 2004 LCD with SD Card - no graphics

  1 view 2 comments 0 points Most recent by Airlight December 2021Repetier-Firmware
• Extrusion Menü verzerrt (v1.2.0)

  1 view 1 comment 0 points Most recent by Repetier_Support December 2021Bug Reports
• Add Note section for each printer (server)

  1 view 1 comment 0 points Most recent by Repetier_Support December 2021Feature Requests