Bug Reports

• Extruder using wrong pin?

  1 view 2 comments 0 points Most recent by 3dGenie December 2022
• Server stürzt ab

  1 view 4 comments 0 points Most recent by 3dGenie December 2022
• Uploading by drag on "Upload G-Code" gives error "size exceeded" when trying to print

  1 view 7 comments 0 points Most recent by Repetier December 2022
• PID Tuning Sovol SV04 Dual Extruder IDX

  1 view 7 comments 0 points Most recent by Roonster December 2022
• Repetier Server 1.4.1 startet alle Drucker neu

  1 view 21 comments 0 points Most recent by Repetier December 2022
• Anycubic I3 Mega startet ständig neu

  1 view 3 comments 0 points Most recent by Repetier December 2022
• Printers stopped for few sec, console message included

  1 view 20 comments 0 points Most recent by pantherius November 2022
• [1.4.2] List of gcode files shown empty after update

  1 view 13 comments 0 points Most recent by NothanUmber November 2022
• v1.4.2. Wiederhergestellter Drucker kann nicht mehr entfernt werden

  1 view 9 comments 0 points Most recent by Repetier November 2022
• Refresh caché of edited files

  1 view 3 comments 0 points Most recent by Repetier November 2022
• Error - Repetier-Server currently not avaliable

  1 view 3 comments 0 points Most recent by Repetier November 2022
• New display of Print Speed on version 1.4.3 labeled F:. Should be labeled as S: for speed

  1 view 3 comments 0 points Most recent by Repetier November 2022
• History with bugs in calendar

  1 view 3 comments 0 points Most recent by Repetier November 2022
• Manual Bed Leveling Wizard

  1 view 3 comments 0 points Most recent by Repetier November 2022
• System Hangup

  1 view 9 comments 0 points Most recent by Repetier November 2022
• Klipper installation friert ein bei Unpacking make (4.2.1-1.2) ...

  1 view 1 comment 0 points Most recent by Repetier October 2022
• Ports get corrupt on Reboot

  1 view 1 comment 0 points Most recent by Repetier October 2022
• New server version causes crashes with all printers

  1 view 14 comments 0 points Most recent by Repetier October 2022
• Loss progress bar in repetier-server monitor

  1 view 3 comments 0 points Most recent by Repetier October 2022
• Tempgeschwindigkeitsberechnung Fehlerhaft

  1 view 3 comments 0 points Most recent by Repetier September 2022
• update auf 1.4.2 kein Wlan

  1 view 1 comment 0 points Most recent by Repetier September 2022
• After Repetier-Server update to 1.4.2, Repetier-Server Monitor 1.4.4 progress bars doesn't work.

  1 view 1 comment 0 points Most recent by Repetier September 2022
• Hotspot and dhcp server problems

  1 view 1 comment 0 points Most recent by Repetier September 2022
• Can't decrease Z-axis below zero with Marlin v2.1.1 until manual G1 command is given

  1 view 1 comment 0 points Most recent by Repetier August 2022
• Probleme repetier Server mit Raspberry Pi

  1 view 2 comments 0 points Most recent by Tobizer August 2022
• Number of prints not updating (v1.4.0)

  1 view 3 comments 0 points Most recent by ITGuruWoo August 2022
• No GCODE previews after updating to Ver. 1.4.0

  1 view 11 comments 0 points Most recent by ITGuruWoo August 2022
• Documentation typo

  1 view 1 comment 0 points Most recent by Repetier August 2022
• Percentage calculation is weird

  1 view 5 comments 0 points Most recent by Repetier August 2022
• Klipper Installation friert ein "gcc-arm-none-eabi"

  1 view 4 comments 0 points Most recent by Repetier August 2022