Bug Reports

• Backup aborted due a failed bakcup of report file

  1 view 1 comment 0 points Most recent by Repetier December 17
• Note in Projects aren't saving

  1 view 2 comments 0 points Most recent by Cryos November 15
• Repetier-Server Monitor 1.4.7 automatischer G-Code Upload funktioniert nicht mehr

  1 view 0 comments 0 points Started by Bjoern_2020 November 3
• Start time not shown correctly in Repetier Server Pro 1.4.18

  1 view 4 comments 0 points Most recent by Repetier October 25
• Repetier-Server Image V38 & GPIO

  1 view 4 comments 0 points Most recent by wiring September 20
• Plötzlich bekommt der Prusa MK3 keine IP mehr vom Repetier-Server

  1 view 24 comments 0 points Most recent by SIEMaker August 31
• Firmware Upload nicht mehr möglich!

  1 view 17 comments 0 points Most recent by Repetier August 12
• Connection Lost

  1 view 1 comment 0 points Most recent by Repetier August 2
• PDF Report not Visible

  1 view 9 comments 0 points Most recent by Repetier July 24
• Unable to see both temperatures on dual extruder

  1 view 3 comments 0 points Most recent by Repetier July 17
• Manual control 'bed' GUI not working

  1 view 2 comments 0 points Most recent by dewrt July 14
• error Klipper State Shutdown

  1 view 4 comments 0 points Most recent by mechatronicfactory July 1
• Prusa MK4 Probleme nach FW Update 5.0

  1 view 7 comments 0 points Most recent by HM_3D June 25
• Brak sterowania sliderem na zakładce Control

  1 view 8 comments 0 points Most recent by Repetier June 8
• "Ausgabe" der Heizelement falsch beim Prusa MK4

  1 view 17 comments 0 points Most recent by 87534 May 31
• Memory leak causes eventual server crash, Repetier Server RPi 3B w/ Prusa MK3S and USB webcam

  1 view 1 comment 0 points Most recent by Repetier May 16
• Rendering never completes after Upgrade to 1.4.16

  1 view 15 comments 0 points Most recent by BobS May 10
• Falsche Bilder im Druckverlauf

  1 view 4 comments 0 points Most recent by Repetier May 3
• Not able to use Remote Access with Static IP after updating

  1 view 3 comments 0 points Most recent by Repetier April 29
• Crash on Receiving Action:Prompt

  1 view 3 comments 0 points Most recent by Repetier April 16
• Repetier server 5.7.0 gpio pin says Unknown GPIO Value yet switches work

  1 view 9 comments 0 points Most recent by TT_Vert April 13
• CallMeBot und Webcam geht nicht

  1 view 3 comments 0 points Most recent by Repetier April 10
• Uploading Gcode stops at 100%

  1 view 4 comments 0 points Most recent by Repetier April 4
• Unable to add Kliper on OEM version 1.4.15 with Armbian 23.11.1 Jammy

  1 view 6 comments 0 points Most recent by Repetier February 26
• push messages via callmebot and signal

  1 view 14 comments 0 points Most recent by DrAdam1986 February 20
• gcode Befehle bearbeiten geht nach Repetier Server update auf 1.4.15 nicht mehr

  1 view 2 comments 0 points Most recent by flyer2000 December 2023
• Temperature Chart shows PWM instead of percent

  1 view 8 comments 0 points Most recent by danym21 December 2023
• Voreinstellungen Kopieren sich selbst

  1 view 3 comments 0 points Most recent by Repetier December 2023
• "Save Configuration" button replaced with "Fix errors to update"

  1 view 1 comment 0 points Most recent by Repetier December 2023
• Prusa / Prusaslicer: Inserting pause at layer (M117; M601) causes server to crash

  1 view 2 comments 0 points Most recent by Repetier November 2023