Toggle navigation
Categories
Discussions
About Us
Privacy Policy
Sign In
Home
›
Repetier-Host
›
Slic3r
Slic3r
«
1
2
3
4
5
6
»
Multiple Objects Positions Changed after Slicing
66
views
3
comments
0
points
Most recent by
Radioman1017
July 2017
Layer height stopping e-motor
33
views
1
comment
0
points
Most recent by
Repetier
July 2017
issues with Slic3r in Repetier-Host V2.0.1
145
views
1
comment
0
points
Most recent by
MartinH
June 2017
Dual Extrudor Not Working Properly
77
views
5
comments
0
points
Most recent by
JwolfUTA
May 2017
перевод на русский
72
views
0
comments
0
points
Started by
jek
May 2017
Layer Range Slicing
58
views
1
comment
0
points
Most recent by
Repetier
May 2017
Where is the Z axis feed rate defined?
119
views
2
comments
0
points
Most recent by
Repetier
May 2017
Speeds seem off. Espically for 1st Layer.
48
views
2
comments
0
points
Most recent by
VectorRoll
April 2017
When trying to print a cylinder always prints it on edge.
34
views
2
comments
0
points
Most recent by
Repetier
April 2017
configuration problem
82
views
1
comment
0
points
Most recent by
Repetier
March 2017
the program doesen't work
79
views
1
comment
0
points
Most recent by
Repetier
February 2017
Scaling causes printing in air
58
views
1
comment
0
points
Most recent by
Repetier
February 2017
Estimated Printing Time has negative value
127
views
4
comments
0
points
Most recent by
Taxus812
January 2017
Measured transient accelerations of approx. 2000 mm/s^2 when the max eeprom setting is 10 mm/s^2
118
views
12
comments
0
points
Most recent by
Repetier
December 2016
PLA OR PETG SECLECTION
73
views
1
comment
0
points
Most recent by
Repetier
December 2016
how to switch T0 to T1 in script or filter?
52
views
1
comment
0
points
Most recent by
Repetier
November 2016
Slic3r Integrated and Octoprint.
239
views
0
comments
0
points
Started by
Pietrogramma
November 2016
Temperature Management for duale extruder
79
views
5
comments
0
points
Most recent by
valerian
October 2016
Nozzle diameter and layer height error
314
views
1
comment
0
points
Most recent by
Repetier
October 2016
Layer 2 no bonding with layer 1 (brim/ramp)
126
views
4
comments
0
points
Most recent by
Repetier
August 2016
Nylon print problems
98
views
3
comments
0
points
Most recent by
Repetier
August 2016
G1 Z 0.400 F7800.000
210
views
8
comments
0
points
Most recent by
Repetier
August 2016
Y-axis center is off
152
views
5
comments
0
points
Most recent by
Israel
August 2016
1.6.2 "Allow different infill extruder for Slic3r"
112
views
0
comments
0
points
Started by
nicksears
July 2016
Printed holes much smaller
183
views
5
comments
0
points
Most recent by
Blisk
July 2016
Printing without alternating raster angle between layers
137
views
1
comment
0
points
Most recent by
Repetier
June 2016
dry run mode
292
views
1
comment
0
points
Most recent by
Repetier
May 2016
can't print without support
111
views
1
comment
0
points
Most recent by
Repetier
May 2016
Big roughs on top layer
203
views
1
comment
0
points
Most recent by
Repetier
May 2016
Slic3r fails to open from RepHost
108
views
0
comments
0
points
Started by
artlab
March 2016
«
1
2
3
4
5
6
»