Slic3r

• 1.6.2 "Allow different infill extruder for Slic3r"

  112 views 0 comments 0 points Started by nicksears July 2016
• Printed holes much smaller

  183 views 5 comments 0 points Most recent by Blisk July 2016
• Printing without alternating raster angle between layers

  137 views 1 comment 0 points Most recent by Repetier June 2016
• dry run mode

  292 views 1 comment 0 points Most recent by Repetier May 2016
• can't print without support

  111 views 1 comment 0 points Most recent by Repetier May 2016
• Big roughs on top layer

  203 views 1 comment 0 points Most recent by Repetier May 2016
• Slic3r fails to open from RepHost

  108 views 0 comments 0 points Started by artlab March 2016
• The model size in gcode is 1 mm different from .stl file model

  116 views 2 comments 0 points Most recent by dominate February 2016
• Too small feed rates for second extruder

  110 views 1 comment 0 points Most recent by Repetier February 2016
• Underextrusion / Extruder jamming ... slic3r question

  178 views 1 comment 0 points Most recent by Repetier February 2016
• Slic3er slicing below bed.

  177 views 2 comments 0 points Most recent by afzalpatil February 2016
• noob question: setting up the ultimaker 2 with slic3r

  858 views 1 comment 0 points Most recent by Repetier February 2016
• Homing the extruder

  169 views 4 comments 0 points Most recent by wholloway January 2016
• Slic3r does not remember changes

  77 views 2 comments 0 points Most recent by Repetier January 2016
• Variable thickness on slanted surfaces

  134 views 2 comments 0 points Most recent by Repetier December 2015
• Z Layer height is changing infill %

  285 views 1 comment 0 points Most recent by Repetier December 2015
• variable z slicing in Repiter host

  117 views 1 comment 0 points Most recent by Repetier December 2015
• Out of Memory

  372 views 3 comments 0 points Most recent by Repetier December 2015
• dualhead not working correctly

  118 views 0 comments 0 points Started by promy November 2015
• How to increase Flowrate for Top Solid Infill only

  603 views 1 comment 0 points Most recent by Repetier November 2015
• Parameters don't change in G code

  102 views 1 comment 0 points Most recent by Repetier November 2015
• Repetier Host & Slic3r - how to split a large STL file

  785 views 2 comments 0 points Most recent by icefire November 2015
• RepV1.5.6 + Slic3r1.2.9

  272 views 5 comments 0 points Most recent by Repetier November 2015
• RepetierHost v1.5.6 & Slic3r 1.2.9 on Linux - Configuration button not working

  712 views 4 comments 0 points Most recent by twforeman October 2015
• Rapide Lite 100 slic3r configuration

  128 views 0 comments 0 points Started by avatarless September 2015
• Slic3r don't write start g-code in repetier

  288 views 1 comment 0 points Most recent by Repetier September 2015
• Broken Slicer Output?

  668 views 10 comments 0 points Most recent by purduecrew September 2015
• i get this error when i try to open slic3r

  597 views 2 comments 0 points Most recent by ruggb September 2015
• multiple extruders (DaVinci 2.0)

  276 views 1 comment 0 points Most recent by RepetierSupport August 2015
• Infill doesn't go all the way to perimeters

  543 views 8 comments 0 points Most recent by LouGeezer August 2015