Slic3r

• No filament feed

  1 view 4 comments 0 points Most recent by dnaman July 2018
• sonam_18

  1 view 6 comments 0 points Most recent by Repetier July 2018
• what settings are required to change for a good quality print for your newly built 3d printer???

  1 view 1 comment 0 points Most recent by Roko July 2018
• Only first filament custom G-code & notes are pass to slic3r when slicing

  1 view 1 comment 0 points Most recent by Repetier July 2018
• Invisible object after slicing

  98 views 12 comments 0 points Most recent by epirie June 2018
• Startup problem / Problème démarrage

  1 view 1 comment 0 points Most recent by Repetier June 2018
• Support Material Offset with Dual Extruder

  1 view 1 comment 0 points Most recent by Repetier June 2018
• Thin Wall settings ??

  1 view 3 comments 0 points Most recent by MartinH April 2018
• Over Extrusion Issue

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Adjust printer to start next layer at the end of the previous layer

  1 view 3 comments 0 points Most recent by Jwolf1987 April 2018
• Missing when filling a layer

  1 view 1 comment 0 points Most recent by Repetier April 2018
• Gaps between layers in print preview

  1 view 3 comments 0 points Most recent by Jwolf1987 March 2018
• Z seam using both slic3r and prusa edition

  1 view 0 comments 0 points Started by flo78 March 2018
• Z depth is only half of capacity

  1 view 1 comment 0 points Most recent by Repetier March 2018
• Prusa Edition Prime Tower problems

  1 view 6 comments 0 points Most recent by Repetier February 2018
• Missing Pieces after slicing

  1 view 1 comment 0 points Most recent by Repetier February 2018
• Inserting Custom G code

  1 view 2 comments 0 points Most recent by Jwolf1987 February 2018
• Random prints from zero point.

  1 view 7 comments 0 points Most recent by Repetier January 2018
• Bed Shape Coordinates

  1 view 4 comments 0 points Most recent by MartinH January 2018
• * appearing on some layers when viewing

  1 view 0 comments 0 points Started by ruggb December 2017
• Extruder only extruding in manual mode after fresh install

  1 view 6 comments 0 points Most recent by Roko December 2017
• Configure AMF file option missing

  1 view 6 comments 0 points Most recent by 3dxstream December 2017
• Slicer and aligning two-color printing

  286 views 18 comments 0 points Most recent by 3dxstream November 2017
• Prime the Nozzles?

  17 views 3 comments 0 points Most recent by Repetier November 2017
• Possible to turn down gap fill amount?

  38 views 4 comments 0 points Most recent by geofox784 November 2017
• No support in Repetier, only moves

  46 views 5 comments 0 points Most recent by Repetier November 2017
• Slic3r configuration files

  89 views 2 comments 0 points Most recent by Repetier October 2017
• What does Slicer do??

  48 views 1 comment 0 points Most recent by Repetier September 2017
• update of prusa edition

  395 views 16 comments 0 points Most recent by Repetier July 2017
• g code for heat bed and fan not generated when using right extruder only

  43 views 5 comments 0 points Most recent by Flybye July 2017